Website & Video: FREE ENERGY Home Generator -Zero Point Energy - Off the Grid - Lutec Australia Pty Ltd Powering The Future

SEE THIS VIDEO - Click HERE for the full video (3MB Shockwave movie in a new window)

WATT METERS FURTHER PROVE THE OVERUNITY ISSUE.


A Center 232 clamp meter reading DC watts as Kilo Watts is inserted in the circuit on the input side and clamped over one of the two leads coming from the power source to the LEA machine.

There is an identical Center 232 meter, reading watts, inserted on the output side and clamped over one of the leads carrying the rectified power that runs the lights that are burning and consuming the output power that is being measured.

The negative volt probe of the input measuring watt meter is connected to the negative lead.

The positive voltage probe of the input measuring watt meter is connected to the positive lead via a diode to ensure negative to positive flow.

The negative volt probe of the output reading watt meter is connected to the negative lead carrying the DC rectified output power.

The positive volt probe of the output measuring watt meter is connected to the positive lead.

The input watts are observed and recorded by the referee.

The output watts are observed and recorded by the referee.

The watt meter on the input side and the watt meter on the output side are swapped over so each measures and confirms the other's previous findings. This ensures the watt meters are reading correctly.

End of test.

or Click HERE for the full video (3MB Shockwave movie in a new window)

A TYPICAL LEA SYSTEM IS 440% OVERUNITY.
(See the LEA page)

This latest video is of a machine that was built independently of Lutec involvement. It demonstrates an efficiency of 240% and that others can successfully replicate the technology.

We have made adjustments so that the input and output are both DC. This means we are able to connect digital Watt meters as seen in the above video that measure in kilowatts the input and output. The Wattmeters are identical, this takes away many objections relating to the method of ascertaining correctly the input and output performance of the LEA.

The meter on the right of screen measures the amount of input power being consumed and reads 0.10 Kilowatts, in watts this represents 100 Watts.

The output meter on the left of screen demonstrates 0.24 Kilowatts. This means the output is 240 Watts.

The image at top right is showing the load applied in the form of light bulbs burning the 240 Watts. What this means is that the output over input efficiency is 240%.

This also demonstrates that if we put a number of these units together, or, build larger ones the output efficiency will remain at this level while the output figure will increase relative to the unit size or number of sections.

An open letter from Lu and John:

We are happy to announce on www.lutec.com.au that after ten years of perfecting our technology and securing patent protection world wide, the time is now right to introduce it to the world.

To increase our changes in being successful in doing so, we ask you to pass on the news about this site to friends, your neighbours, your local radio and TV talk current affairs and morning talk shows, and to contact your local newspaper and your local government representatives, so they too have the opportunity to support the technology as a real alternative to green house gas producing polluters like coal and oil, and the possible catastrophic dangers posed by nuclear fired electricity power stations break down. The LEA can amplify electricity produced by conventional or alternative means.

Please help us to restore our fragile environment.

Ten more years at the current growth rate of green house pollution will kill us all. It must be dealt with now. That is right now!! Even if we stopped polluting today it would take thirty years for the earth to recover. That’s Thirty years. But it won’t happen that way will it? There is no way it will stop tomorrow, but it must be stopped or we humans as a species, and nearly every other species on earth are doomed.

It is therefore vitally important that you/we make people who count aware of the LEA technology.

Now that we are ready to showcase our technology it is time to act. Others, who support the coal, oil, and uranium industries are lobbying government’s world wide to push their own agendas. They have years of experience, and the know how, financial backing and networks to help them to “play the game” Remember Big Business does not take kindly to what they see as competition. In reality what we propose for our technology actually helps them to extend their resource life and by so doing make them more money. Take oil for example, what if the diminishing supply could last for an extra ten years, what would it be worth a gallon or litre then? We are not in opposition to these people, we want to fit in alongside them and help them as well.

Well, the good news is the people of the planet are the customers, and the customer is always right. Without consumer support no business can survive. Without public support no government can survive. People power is everything. We don’t say there is no place for oil, uranium or coal, on the contrary there most definitely is. We do say that what we have and are desperately seeking assistance to introduce, is a means of being more efficient in how we control, release and consume the resources available. Let’s become smarter in the way we handle what we have.

If we don’t we can forget about squabbles between the major religions, the different cultures, terrorists versus the rest, and the constant striving for more and more wealth by big multinational companies fuelled by their shareholders expectations of more and more higher dividends. Because there will be nothing on earth left to breathe, to eat, to drink.

If you too are serious about helping to restore the earths God given ability to process, purify, heal and restore, and to immediately begin to take steps to help minimize the impact of Global warming, with a view to eventual complete restoration, then we’re on the same side.

That means we hope you can give a small part of your time toward simply informing your network of contacts, your friends, family, media, politics, and business, wherever you are on earth, to help spread the word about the potential of this technology.

Send them this site address. Insist they reply to you confirming they have seen it.

We will back you one hundred percent and demonstrate what out technology can do to anyone who you send our way, who can show us they are willing and able to help in other ways of support such as; Purchasing licenses to commercialize the technology, or providing finance through involving themselves in investment opportunities. Or by exerting influence, or maybe they are interested in manufacture, distribution and sales of product. Such people will either be high net worth corporations or individuals. The man in the street, someone who wants to help in this way can do so, but will need to make direct enquiries by email to find out how.

It is our firm belief that we will find through these pages a group of determined and willing people, who are intelligent and far sighted enough to see, and have heard all the talk about the hopelessness of the situation, but who can dare to believe that we have a solution to the problem right here, right now. A solution that can address at least part of the problem, and bring with it hope.

Collectively as citizens of planet earth we simply can’t afford to wait for “someone else” to fix this living growing cancerous problem. Together we can and will make a difference and succeed. We can’t do it by ourselves because there are only two of us, but it will only take for people like you to do just a little bit and success will follow.

Best wishes to all for a future.

Lu and John at Lutec.

November 2006.

• Please check out the 'Heroes' page for information about how you can help save the planet...

CONTACT US: http://www.lutec.com.au/contact.htm
HOW IT WORKS: http://www.lutec.com.au/how.htm
TECHNICAL DATA: http://www.lutec.com.au/tech.htm
APPLICATIONS: http://www.lutec.com.au/buttons/button15.jpg
L.E.A: http://www.lutec.com.au/buttons/button13.jpg
ENVIRONMENT: http://www.lutec.com.au/enviro.htm
PATENTS: http://www.lutec.com.au/patents.htm
OPPORTUNITIES: http://www.lutec.com.au/invest.htm
HEROES: http://www.lutec.com.au/heroes.htm
HOME PAGE: http://www.lutec.com.au/index.htm

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

HEAP ENERGY FOR SALE!
Lu Brits and John Christie

Original version

Source : http://www.yowusa.com/Audio/lutec/lutec_update.html

Dear Friends of Lutec:

There is a web site www.yowusa.com that we suggest will be of interest to you. It is downloadable so you can listen to a web radio interview featuring Marshall Masters interviewing Jacco Van Der Worp, a Dutch physicist and systems failure analyst who, after lengthy telephone consultations with Lou, has examined the physics behind the control system used in Lutec motors, and has confirmed the validity of the technology. Basically Jacco concludes from an academic stand point, that the controlled periodic interruption of a rotating permanent magnetic field, by the temporary and precise introduction of another magnetic field, causes the secondary effect of the naturally occurring polarity flip of the permanent magnet influence, to be accessed, harnessed, and applied to assist in the rotors on-going revolution direction. And most importantly, he agrees that this flip effect is influenced by voltage rather than current, and also allows the flip back to the original polarity to naturally occur at no cost of current, so the rotor is driven onwards at a very small cost of electricity.

This magnetic field effect is what is covered in our patent applications, but has never before been publicly reviewed by an academic of standing. It is very encouraging to have a notable qualified academic put his name to it, and we are thankful to him for doing so. Over the years there have been several other academics, including one of the world’s most notable professors of power electronics, who after evaluating our technology like Jacco Van Der Worp, also agree with us that it works. Commercial confidence arrangements made by the people paying for that particular analysis prevent us from commenting publicly on their findings, other than to say that the mathematical formula we use to prove the input current, and the method we use to prove the output are correct and irrefutable.

The overall effect of all this allows the motor to run for a relatively insignificant cost of input energy compared to any other electric motor. It is what is causing the Lutec motors and generators to produce such high relative electrical output compared to input, and to run cool. Because fluctuating current is present in the copper coil windings of electric motors there is always significant heat loss evidenced as the coil windings become hot as the motor runs, and even hotter as a load is applied. The heat so evidenced is wasted energy and is found in every other electric motor. If heat is present in the coils, a motor simply can not be over-unity.

All the coil windings in the prototype Lutec motors and generators demonstrate the remarkable ability to run cool, even when subjected to maximum possible load. They all clearly evidence the technology having superior performance characteristics than any other motor, and that is because of the rotating magnetic field control. And that’s what Jacco refers to when he says. “They have done it, they have pinned it down”.

Free energy or free electricity. Jacco says it is not a free energy machine. When Lou and I talk of free energy we are meaning free in monetary terms. We are not saying zero point energy, or ether energy, or that any other mystical energy as yet unmapped is being tapped. What we have is a free energy machine because the majority of the energy/electricity produced by a generator using the patented technology costs next to nothing to produce. That’s close enough to free for me.

In the example quoted by Jacco Van Der Worp 15 times more output than input is given. We know that we can get much bigger returns than that. In fact at present we are demonstrating 19 to 20 times more output than input, using a switching system Lou has designed. It is not solid state electronics, but may yet prove to be suitable to go into the production of a home use size electricity generator.

As a further matter of interest and contrary to Jacco’s comment, this specific means of controlling a rotary device was never “stumbled” upon, it was actively and purposely sought out by Lou, and then further researched, documented, developed and adapted for practical demonstration by Lou and myself. The over unity (more than 100% efficiency) effect displayed and now confirmed by applied physicist Jacco Van Der Worp as having validity was always the goal.

For those technical types it actually displays a pure coefficient of performance by combining three separate field effect characteristics. So we would say that if one was using the terminology of the day, then technically it’s not a free energy machine, but a highly efficient machine with a C.O.P. of 20+ or able to produce 20 times more output than input.

The politics and opinions of Marshall Masters are not those of Lou and me and although we are very pleased he has gone to the trouble to try to help get our technology “out there” there are some comments made on the interview that need clarification by us here.

Firstly the “University” did not just disappear and not want to do any more work on the project. It seems Marshall has misunderstood Lou during a previous interview or on a phone call, and he then thought we were involved with a University here in Australia, and that university has for some sinister reason pulled the plug. That is not so. There is one University where we have very good relations with some of the teaching staff, and still do.

We did engage the services of a private company made up of honors graduates from another Australian university, who have elected to withdraw from their contract to provide a solid state switching system for the motor. It appears their reasons are more from a commercial view than for any other. They certainly have not disappeared.

Marshall also uses very emotive terms including kill off, wipe out, squash and so forth to describe what he thinks is happening to us behind the scenes, and also reckons the US President and Australian government is actively trying to stop us. I doubt this is correct, if they really wanted to do so, they could in a flash and there wouldn’t even be a ripple to show their passing.

Admittedly we have had no direct support from the Australian Federal government or from the Queensland State Government, but we don’t expect any in any case. That’s because our country has a history of letting many of its best ideas go overseas, and having to buy the technology back. There is nothing sinister in that, just a lack of systems within government to allow private individuals to access government assistance. For example they won’t sign non disclosure and confidentiality agreements. This is standard procedure in the world of commerce, designed to protect the interests of inventors. They claim the public service act prevents government employees from talking about confidential matters. Yeah right. The penalty for breach is a paltry ten thousand dollar fine. Selling the secrets of the Lutec technology before patents were in place could have made a dishonest or desperate public servant an overnight multi millionaire, and disqualified us from being able to obtain patent protection over our invention. That makes it difficult to progress a technology with government assistance when you are a struggling inventor.

If the Federal government that had invested one million dollars in Lutec technology five years ago, and so sped up the development, production, manufacture, and sale of the products using the technology, the return may have made them a thousand times the investment by now. And also gained international kudos, green house credits to burn, helped save the planet, provided electricity through the biggest storms and disasters, and backed up the ailing grid power system. Imagine the political brownie points they could have gained with the Australian people, you wouldn’t be able to get them out of power with a crow bar. . Jacco Van Der Worp estimates that there is the need right now for millions of these little generators in the USA alone, there is no doubt he is right. Do the sums for yourself. Government taxes earned and the flow-on effect from employment of the huge labor force needed to support the massive potential for export, would amount to billions of dollars in government earnings. Even the revenue generated from coal exports would not be slowed one iota, because producing small home size generators to every new dwelling built in the USA would alone account for millions of units. That’s just the growth in private housing, not the existing demand, and not even taking into account the growth in industry that is also caused by natural population growth. It seems Australia has missed the boat, although we are still open to them, but there must be countries and companies or corporations out there that would love to have control of this technology. Give us a call and we’ll talk.

Where we stand right now is that we do need a million dollars to complete the technology to where we want it before releasing it in the form of a generator. Jacco is dead right in his evaluation there. We are not looking for a free hand-out, so if you dear reader know anyone who might be interested in becoming involved, with a minimum one hundred and fifty thousand dollars available to contribute, please have them email us at info@lutec.com.au and request information. We will also need their full names, address, and contact phone numbers, this tends to keep the tire kickers away. Enquiries from outside of Australia are welcome.

Please listen to the interview between Marshall Masters and Jacco Van Der Worp, it is certain to be interesting and educational, exciting, and encouraging for those waiting for clean green sustainable energy to finally be introduced and to improve their own, their children’s and grand children’s quality of life and assist our global environment.

I apologize for my slackness in replying to your emails. The stream of mail has slowed comparative to the early days, but even so is still daunting and generally the writers ask questions that are answered on our web site, so I don’t answer those. Any questions of a technical nature should be referred to Lou for him to answer, that might make things work a bit faster.

Thanks for taking the time to read this far.

John and Lou.
June 2005.

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

"New Magnetic-Electric Device Offers Near Free Energy Source"
by Penny Robins
The Cairns Post (Northern Queensland, NZ ~ 3-8-01)
Go to this webpage to see photos and technical diagrams: http://www.rexresearch.com/christie/christie.htm

Two Cairns inventors yesterday unveiled a world first commercial machine which can power a house from a permanent, clean, green and virtually free energy source. The machine, developed by Brinsmead mechanical engineer John Christie and Edge Hil electrician Lou Brits, has an international patent pending and is expected to go on the market for $4000-$5000.

Relying on the attraction and repulsion of internal magnets, the Lutec 1000 operates continually on a pulse-like current 24 hours a day - producing 24 kilowatts of power - once it is kickstarted from a battery source. The device is more than 500 per cent efficient, compared to a car which is less than 40 per cent efficient and loses power through heat and friction. No powerlines would be needed to distribute energy from the individual power sources. There is no heat, harmful emissions or airborne matter in the transmission. If it were not for the magnets, which have a life of 1300 years, and the battery pack, which has a life of about five years, the machine would be in perpetual motion.

A demonstration of the motor from the carpeted study of Mr Christie's Brinsmead home revealed the device in all its glory - bigger than the average cyclone back-up generator but much less noisy. M Christie and Mr Brits have been tinkering together on the motor in their spare time since they met in a Sheridan St cafe five years ago and began sharing ideas. One and a half years ago, the design was perfected and the pair lodged a patent with Brisbane patent attorneys Griffith Hack. Mr Christie said the next step was to develop a small-scale pilot plant in Cairns to begin distributing the motors to the places they were needed most - such as shops and homes in the power-starved Daintree region and the Torres Strait. He said the price tag for the devices could vary in remote locations depending on government rebates, freight and installation costs.

The beauty of the device was that it was transportable and could be packed in a removalist van along with other earthly possessions when moving house, he said The only problem the pair now face is in raising $500,000 to start their production plant. "We're trying to keep it local, and trying to keep it in Australia, but it's hard because, offshore, they are more aggressive in taking up new initiatives," Mr Christie said.

Already, the invention has received interest from the United States, China, Japan and Indonesia. "But we want to set up here and put the product on the market first, and then we'll take it to the world," he said. Mr Christie said it had been hard to keep a lid on the invention which had such a huge potential in the quest for clean, green, energy production. He said he and Mr Brit also feared the worst once they realised the significance of their invention. "We were afraid the kids would be kidnapped or we'd be shot, I'm not kidding," he said. "You hear horror stories about people running up against fuel companies, but it's all hogwash --- people in the main are desperately looking for technologies that will help our environment."

The pair have begun discussions with Ergon [ the local electricity supplier utility] as there is also the opportunity of selling energy back to the grid. Mr Christie said the average home with a pool needed only 14kW of energy per day - which meant a 10 kW daily excess would be left over during the generation process

Griffith Hack partner Cliff Carew, who was speaking from Brisbane, confirmed the device was genuine and unique. "An international application has been lodged, they've conducted an international search and haven't come up with anything similar, so it would seem to be a new concept," Mr Carew said. He said it would be another two and a half years before the patent was recognised in 140 countries around the world - the usual length of time for an international patent to be processed.

Lou Brits (left) and John Christie
The Cairns Post ~ Two Cairns inventors who say they have developed a radical new energy generating machine have been swamped with inquiries over the past 24 hours since going public with their discovery.
One Cairns businessman already has offered a substantial sum of money to bankroll the establishment of a factory to produce the new generator.

He was among a crowd of curious Far Northerners who rushed to contact Edge Hill electrician Lou Brits and Brinsmead mechanical enginner John Christie once news of their invention broke in the Cairns Post yesterday.
Investors, people with scientific backgrounds and those who were keen to buy one of the new Lutec 1000 machines to power their homes swamped the Cairns Post and the two inventors, who work from home, with their calls. The generator is capable of producing 24 kilowatts of energy per day and is powered by the alternating attraction and repulsion of internal magnets once it is kickstarted from a battery source.

It has more than twice enough energy to power the average family home, while remaining free from heat, emissions or airborne matter. Mr. Christie said he and Mr. Brits realised their invention "flew in the face of physics" by being 500 per cent efficient - but it worked.

"The phone hasn't stopped ringing." Mr. Christie said yesterday afternoon. We've had calls from the Daintree - people wanting to place orders and buy them. We're happy about that but, really, we're not in the position to take orders."

Mr. Christie said he began receiving phone calls from 7:30AM yesterday (when the story was first reported).

Mr. Christie said people begain arriving unannounced on his doorstep from 8:30AM.

He said two people he had never met before had even needed to be ushered out of the room just after 9AM when he went on air for a radio interview.

An international patent is pending on the invention and the two men already have received interest from overseas.

But Mr. Brits and Mr. Christie say they are keen to setup a production plant in Cairns to produce the machines on a small scale to power homes in remote areas of Queensland like the Daintree region and in the Torres Strait.

Cairns businessman Alex Roma yesterday said he was prepared to help bankroll the production plant as it was an opportunity to expand industry in the Far North.

Ahead of meeting the two inventors late yesterday, Mr. Roma said if their invention stacked up, he was prepared to up up "a large sum" to help make the local production plant a reality.

"Looking at this, it's fantastic," he said. "I've always said Cairns needs a boost in industry - it's one thing Cairns is lacking. We'd employ local people and produce something we could export apart from sugar cane and seafood."

Mr. Roma said an opportunity existed to produce locally not just the machines but all of the accompanying components.

Member for Leichhardt Warren Entsch lent his support to the proposal to develop a plant to manufacture the clean, green power generators in Cairns.

Ergon Energy spokeswoman Sara Collins said discussions were ongoing with the inventors, who hope to sell excess power back to the grid.

The Inventors
( Source: www.lutec.com.au )

John Christie (left) is the co-founder, CEO and chairman of Lutec (Aust.) Pty Ltd.
Education: Auckland Technical Institute, Mechanical Engineer.

He has a vast experience in operating small businesses, is on the boards of FNQ Outreach Limited and Trinity Care Association, and is a director of Technology Trading International Pty., Ltd.

His business history includes introducing light steel framed building systems into North Qld., Co-Designing and patenting a new light steel frame construction system subsequently sold to the US.

He co-designed, developed, and made patent application for a new form of wind turbine.

He was Managing Director of Tarinfile Pty., Ltd., the owner of True Blue Sheds a successful North Qld company specialising in manufacturing, marketing and selling steel framed farm buildings, and low cost housing mainly to rural and remote communities.

He has also held middle management positions with the Australian Broadcasting Commission.

Ludwig (Lou) Brits (right, above) is the co-founder, managing director and head of development of Lutec (Aust.) Pty., Ltd.

He is Chairman and director of TTI Pty., Ltd. TTI Pty Ltd is a state government recognised R.A.P. (remote area power) system provider.

Education: Mechanical and electrical engineering and trade certificates (Europe).

Mr Brits has had a varied international career including running hydro electric power stations, designing and manufacturing various electrical components for power stations. Maintaining power stations.

He is an inventor of many and varied objects and products including a wind powered turbine system, electronic health care products, water treatment systems, and hydro/organic fertilizing/pest control products.

He has a wealth of talent and inventive genius, and is well regarded and highly respected by those he works with.

Lutec Pty., Ltd: "How It Works"
( Source: www.lutec.com.au )

We have never said there is an "endless" source of energy emanating from magnets. We have said that the magnets we use in the Lutec 1000 are able to maintain their magnetic qualities for over twelve hundred years. That is a long time when gauged by human life expectancy, but is not forever. We welcome informed opinion, and to that end have sought out the highest qualified people in Australia and the United States of America to review our work.

The Lutec 1000 only baffles those who misinterpret the actions taking place within it as being outside common scientific principles and laws, where in fact it certainly is not. We will try to make a simple explanation to demonstrate what motivates the Lutec 1000 motor/ generator:

Let’s say we hang a ten kilo weight off a permanent magnet butted to a steel roofing beam, and that the only thing holding the permanent magnet to the steel beam is the magnetism. Now let’s do the same thing, but this time with an electro-magnet which requires a constant electrical input to maintain its magnetic qualities.

Let’s say we leave them both there for ten years"

They will both perform the same task, that of holding the ten kilos off the floor. The electro-magnet, however, has needed to be fuelled by electricity provided by a generator of some kind - it could be hydro, nuclear, wind, solar, coal or oil - and has cost a large amount in terms of energy. Much work (in the scientific sense) has been done to provide the constant electric current necessary to maintain its magnetic hold on the steel girder.

Now take notice, the permanent magnet has not needed to be energised by an external source, it has done the job for free" using only the magnetism it contains to perform the same job. The clue here is in the title of "permanent" magnet.

That same principle is one of the reasons the Lutec 1000 motor turns, it is of course the spinning of the centre core of the motor which is caused by the permanent magnets being attracted and then repulsed from the steel cores of the fixed stator coils. It is this primary movement that allows the magnetic fields around the stator coils to be "cut" by the effect of the permanent magnets sweeping past the steel cores of the coils.

Note that we have achieved two effects from one cause, thus inducing an electric current per Mr Faraday’s theory, and so generating electricity as an output or product of the motors motion. The only electricity consumed has been that required to temporarily charge the coils and so creating a temporary magnet of like polarity to cause the permanent magnet to be repulsed rather than attracted.

There are a couple of other major factors that we won’t go into here, suffice it to say that our current prototype demonstrates 1500% more "out" than "in"...

For the technically-minded, the following formula is used to determine consumption of input power:

If the waveforms are periodic with constant rotational speed of the machine and constant mechanical load on the output, then a calculation of energy usage over one full rotational cycle should suffice. Along with all previous assumptions remaining valid, the formula then becomes:

(where W(T) represents the net energy usage in joules over one period T).

Lutec Skeptics Challenged
(Unidentified source)

Inventors of the controversial Lutec fuel-free energy generator have thrown off the machine's cover and invited sceptics to air their doubts when the generator is publicly displayed later this year.

The Lutec 1000 has been refined and redeveloped for the sixth time and inventors Lou Brits and John Christie say the machine is almost ready for release. They are also inviting qualified electricians to personally contact them about becoming licensed installers for the Cairnes area.

The sixth generation Lutec 1000 now stands one metre tall (in an upright position) and has a steel frame which has allowed the inventors to attach more magnets closer to the drum to increase the power generation capacity.

Mr. Christie said the 'switches' used to supply the energy into the drum-shaped machine were also becoming smaller and more compact.

The new-look Lutec should be completed by the end of the month and the inventors hope to display all six generations of the machine at the Hilton Hotel later this year.

While Mr. Christie is eager to silence the critics with a public demonstration, he must wait for international agreements to be finalized.

However, he did invite the 'doubters' to see the machine work in person, saying patents were now pending in more than 100 countries, and he could provide detailed information of experts who could verify their work.

'They are welcome to contact us and we will give them the names of experts who have assessed the machine, but who's going to pay the experts, who are paid more than $US90 an hour, to sit down and explain it to them - because we're not,' Mr. Christie said.

'We don't mind people criticising the machine, but no one who has come to see the motor has gone away still believing it would not work.'

Mr. Brits said the crux of the disbelief centred around the perception that the Lutec 1000 created energy - an assumption which was essentially flawed.

'They are not taking into account the combination of the capabilities of permanent magnets and the effects on the incoming current caused by the induction of a greater current caused within the motor,' he said.

'All people see is the amount of energy we are putting in and more coming out. They then wrongly assume that we are creating energy.'

The core of the Lutec 1000 spins as the magnets - spaced alternately around the drum - are attracted then repulsed (using a small electrical circuit) to steel cores which are off-set above the centre down.

Mr. Brits said the machine released the energy stored in the magnets and anyone who doubted the 'stored energy' should try holding a piece of steel off the ground for an extended period.

'In the same way as a person holding a weight uses energy while they are not moving, a magnet uses energy to attract and hold a piece of steel,' he said.

'And it's absolute nonsense that a magnet can only be used on once. Everybody knows if you take a fridge magnet off the fridge and put a new piece of paper under it, it still sticks as good as new.'

A recent demonstration showed the inventors were modest in claiming a 400 per cent increase in energy output, with the Lutec 1000 lighting up six light bulbs (360 watts) with an input of just 42 watts.

Mr. Brits admitted the magnets would run out of 'energy', in approximately 1300 years, but could be recharged with an electrical current.

Mr. Christie said he and Mr. Brits had recently been approached by a company whowere interested in adapting the Lutec to power machines used in space exploration and he believed eventually the generator could be used in motor operated appliances.

The Environmental Protection Agency had also assessed the machine with the intention of giving inertial household users rebates or 'green house credits'.

He said the size and capability of the machine could be changed to suit the need and envisioned a household full of Lutec 1000's.

'Things like your fan could have a Lutec motor and the excess energy created could go back into a household battery to run static appliances like your television.

'It is certainly possible that it could remove a household from the power grid completely.'

For more information visit the website at:
http://www.lutec.com.au

Lutec Newsletter
Vol. 1(1), February 2002
( Source: www.keelynet.com )

It has been almost a year since many of you first registered your interest in the Lutec technology phenomenon. We apologize for the long delay in preparing this much awaited newsletter. We can only say that we share your frustrations as the past year has been mainly spent trying to source venture capital to get the Lutec revolution underway.

Sadly, we have to report that it is almost impossible to obtain financial support for a "green fields" technology based on new technology in Australia.

However, the year has not been wasted by any means. Lou and John have continued development of the Lutec 1000. The solid state switching has been designed, built, tested and installed onto the machine with the results to output exceeding expectations. The machine itself has also undergone a number of design refinements which ahve all added to improved efficiency.

Finally I can report that the manufacture of these generators has been awarded to a Cairns electrical manufacturer with prodcution expected to start by the end of this financial year. Initially the rate of production will be limited to only 10 per month, but we expect to increase this to 250 per month as demand and capital allow.

We hope to have one of the new Lutec 1000 electrical generators on permanent public display commencing from the end of April.

For those of you waiting for the opportunity to acquire one of these electrical generators, please act quickly as weexpect demand to far outweigh supply and the waiting period for delivery may be as much as 6 months.

Fortunately the international interest in this new revolutionary technology far exceeds the apathetic approach shown by Australian entrepreneurs.

We can now report that a licensing agreement is now in place for the manufacture and sale of the Lutec technology within America.

Negotiations for the rights to Southeast Asia and Europe are ongoing with a number of interested companies and we expect these to be finalized by the end of 2002.

It is only this interest which has allowed Lutec Australia to commence operations.

( Equivalent: US Patent # 6, 620,806 issued October 7, 2003 )

A System for Controlling a Rotary Device

World Intellectual Property Organization
International Application # WO 00/28656
Publication Date: 18 May 2000
International Application # PCT/AU99/00962

Applicants & Inventors:

BRITS, Ludwig (3/13 Springfield Crescent, Whitfield, Cairns, QLD 4870 Australia)
CHRISTIE, Victor John (7/34 Springfield Crescent, Whitfield, Cairns, QLD 4870 Australia)

Agent: Griffith Hack, GPO Box 3125,Briscbane, QLD 4001, Australia

Abstract --- A system for controlling a rotatable device, the system comprising a controller and a rotary device, which has a stator and rotor, wherein the controller is connected to the rotary device to control rotation of the rotary device, and wherein the controller is adapted to periodically energize at least one energizing coil of the device to create a magnetic field of a polarity which induces the rotor to rotate in a single direction and wherein the controller is switched off so as to de-energize the energizing coil when other forces, being forces other than those resulting from the energized energizing coil, produce a resultant force which induces rotation of the rotor in the single direction.

Field of Invention

The present invention relates to motors which are used for generating a torque and generators used for generating electricity.

Background of the Invention

A typical electric motor consists of a stator and rotor.

The operation of an electric motor is based on the principal that an electric current through a conductor produces a magnetic field, the direction of current in an electromagnet such as a coil of wire determines the location of the magnet poles and like magnetic poles repel and opposite poles attract.

The stator which is typically called the field structure establishes a constant magnetic field in the motor.

Typically the magnetic field is established by permanent magnets which are called field magnets and located at equally spaced intervals around the rotor.

The rotor or armature typically consists of a series of equally spaced coils which are able to be energized to produce a magnetic field and thus north or south poles.

By keeping the coils energized the interacting magnetic fields of the rotor and the stator produce rotation of the rotor.

To ensure that rotation occurs in a single direction a commutator is typically connected to the windings of the coils of the rotor so as to change the direction of the current applied to the coils.

If the direction of the current was not reversed the rotor would rotate in one direction and then reverse its direction before a full cycle of rotation could be completed.

The above description typifies a DC motor. AC motors do not have commutators because alternating current reverses its direction independently.

For a typical AC motor such as an induction motor the rotor has no direct connection to the external source of electricity. Alternating current flows around field cols in the stator and produces a rotating magnetic field. This rotating magnetic field induces an electric current in the rotor resulting in another magnetic field.

This induced magnetic field from the rotor interacts with the magnetic field from the stator causing the rotor to turn.

An electric generator is effectively the reverse of an electric motor. Instead of supplying electricity to coils of either the stator or the rotor, the rotor or armature is rotated by physical forces produced by a prime mover.

In effect a generator changes mechanical energy into electrical energy.

Summary of the Invention

The present invention is aimed at providing an improved rotary device which operates with improved efficiency compared to conventional rotary devices.

The present invention is also concerned with providing a system for controlling a rotary device which is able to generate electrical and/or mechanical energy.

According to the present invention there is provided a system for controlling a rotary device, the system comprising a controller and a rotary device, which has a stator and rotor, wherein the controller is connected to the rotary device to control rotation of the rotary device, and wherein the controller is adapted to periodically energize at least one energizing coil of the device to create a magnetic field of a polarity which induces the rotor to rotate in s single direction and wherein the controller is switched off so as to e-energize the energizing coil when other forces, being forces other than those resulting from the energized energizing coil produce a resultant force which induces rotation of the rotor in a single direction.

Preferably the controller is adapted to energize the energizing coil for a period which the resultant force from the other forces acts to rotate the rotor in the opposite direction, whereby the force applied by the energizing coil overcomes (is greater than) the resultant force.

The controller is preferably adapted to switch off to de-energize the energizing coil before the resultant force is zero.

The controller preferably is adapted to switch off to de-energize the energizing coil for a period before the resultant force is zero, and to allow back EMF induced by other forces to urge the rotor to rotate in the single direction before the resultant force is zero.

Preferably the resultant force excludes forces arising from back EMF.

The energizing coil may be adapted to be energized by the controller through a predetermined angle of a complete revolution of the motor.

Preferably the/each energizing coil is energized more than once during a single revolution (cycle of the rotor.

The/each or at least one energizing coil may be energized each time the resultant force applies a force to the rotor in the opposite direction.

The/each or at least one energizing coil may be energized by a periodic pulse applied by the controller.

The periodic pulses are preferably all of the same sign.

The/each or selected ones of the energizing coils are energized whenever the resultant force is in the opposite direction and then for a period less than the period during which the resultant force changes from zero to a maximum and back to zero.

According to one embodiment the stator has the at least one energizing coil.

The rotor may have at least one magnetic field generating means which is able to generate a magnetic field which interacts with the magnetic field generated by the/each energizing coil when energized, to apply a force to rotate the rotor in one direction.

The/each energizing coil preferably includes a magnetic interaction means which is adapted to either repel or attract the magnetic field generating means.

The magnetic interaction means may comprise a ferrous body or body of another substance which is attractable to a magnetized body.

The magnetic field generating means may be a permanent magnet.

The magnetic interaction means may be an iron core or a permanent magnet.

Preferably the magnetic field generating means comprises a permanent magnet, or member attractable to a magnetized body.

The stator preferably comprises a plurality of energizing coils evenly spaced around the rotor.

Each energizing coil is preferably an electromagnet.

Preferably the or each energizing coil includes the magnetic interaction means through its coil.

Preferable the rotor comprises a plurality of evenly spaced magnetic field generating means.

According to one embodiment the rotor comprises a plurality of evenly spaced permanent magnets.

The evenly spaced permanent magnets may all be of the same polarity.

The evenly spaced magnetic field generating means may be energizable coils simulating magnets.

Preferably the poles of the magnetic field generating means are all the same.

The magnetic poles produces by energized energizing coils may be the same as that for the magnetic field generating means.

According to an alternative embodiment an alternating pattern of poles for the energizing coils is provided.

According to another embodiment an alternating pattern of permanent magnets is provided for the rotor.

According to a further embodiment of the present invention the stator has a plurality of magnetic flux generating means.

The magnetic field generating means for the stator may be permanent magnets.

Preferably the rotor may be an armature and the stator may be a field winding.

Preferably the rotor magnetic field generating means is energized by an external power supply being DC or AC current.

The stator magnetic interaction means may be energized by coils operating on AC or DC current.

According to one embodiment the stator includes at least one induction coil which adapted to have current induced therein by the magnetic field generating means of the rotor.

The/each induction coil may be separate from the/each energizing coil.

The/each induction coil may also be an energizing coil.

The/each energizing coil may be adapted to be connected to an output circuit whereby current induced in the/each energizing coil is output to the output circuit.

It is preferred that switching circuitry is adapted to rectify current induced in the induction coils.

It is preferred that the rectifying occurs just before the or each energizing coil is energized by the power supply.

Preferably current output to the output circuit is adapted to be used to run an electric device.

The controller preferably comprises a switching circuit which is adapted to connect the/each energizing coil to an output circuit when no current is generated to energize the energizing coil.

Preferably the controller provides a switching circuit.

The controller may be a rotary switch.

The rotary switch may have at least one contact which is aligned with the/each magnetic field generating means.

Preferably the rotary switch has at least one contact aligned with the permanent magnets of the rotor.

The rotary switch may have the same number of contacts as the number of magnetic field generating means; being magnets in their preferred form.

The/each contact may have a switch that varies with vertical height.

The rotary switch may have the same number of contacts as the number of magnetic field generating means; being magnets in their preferred form.

The/each contact may have a width that varies with vertical height.

The rotary switch preferably comprises adjustable brushes which are able to move vertically.

The contacts preferably from a top end to a bottom end thereof.

The rotary switch and rotor may be located on coaxial central axis.

The rotary switch and rotor may be mounted on a common axial.

Preferably the rotor switch is mounted in a separate chamber from the rotor.

According to one embodiment each energizing coil is adapted to repel an adjacent magnetic field generating means when energized.

Each energizing coil may be adapted to be energized by back EMF for only a predetermined period of each cycle.

The predetermined period preferably occurs after current to the energizing coil is switched off.

According to a further embodiment the/each energizing coil is adapted to attract the magnetic field generating means of the rotor.

The present invention contemplates a number of variations of the components making up the systems described above. For example, the current, voltage, magnetic field generated, the number of poles of magnets for the rotor/stator may all vary and accordingly will affect the timing of switching of energizing coils.

The rotary device may have a greater number of magnetic poles generated on the stator/field winding than in the rotor/armature or vice versa.

According to one embodiment the number of poles on both of these are the same.

It is preferred that the switching of the energizing coils which is controlled by the controller is adapted to maximize the influence of back EMF produced.

It is preferred that the energizing coils are effectively provided with a pulsed electric current of minimum duration, which duration is enough to maintain rotation of the rotor and produce a desired output of torque or current.

Brief Description of the Drawings

Preferred embodiments of the present invention will now be described by way of example only with reference to the accompanying drawing in which:

Figure 1 shows a cross-sectional front view of a rotary device and control thereof in accordance with a first embodiment of the invention;

Figure 2 shows a top view of the controller shown in Figure 1;

Figure 3 shows a side view of the controller shown in Figure 1;

Figure 4a shows a schematic view of a system for controlling a rotary device in accordance with the first embodiment of the present invention;

Figure 4b shows a schematic view of the rotary device shown in Figure 4a;

Figure 5 shows a graphical representation of force versus angular position of permanent magnet M1 of the system shown in Figure 4a;

Figure 6 shows a series of four graphs of input current versus angular movement of each permanent magnet of the system shown in Figure 4a;

Figure 7 shows a graphical representation of input voltage versus input current for each coil of the rotary device shown in the system of Figure 4a;

Figure 8 shows a schematic diagram of variation of natural magnetic attraction versus angular displacement of a rotor having a single permanent magnet and a stator having a single energizing coil, in accordance with a second embodiment of the present invention;

Figure 9 shows a graphical representation of magnetic field versus angular displacement in accordance with the second embodiment of the present invention;

Figure 10 shows a graphical representation of induced induction versus angular displacement of the permanent magnet in accordance with the second embodiment of the present invention; and

Figure 11 shows a further graphical representation of induced induction of electro-magnetic force versus angular displacement of the permanent magnet in accordance with the second embodiment of the present invention.

Detailed Description of the Drawings

As shown in Figure 4a according to the first embodiment of the invention a system is provided consisting of a rotor 11 having four permanent magnets M1, M2, M3, M4 which are evenly spaced at 90° with respect to each other.

The system includes a stator 12 consisting of three electro-magnet energizing coils A, B, C which are spaced 120° apart from each other.

Each coil A, B, C is connected in circuit with a power supply of 54 volts and a switch RS1, RS2, RS3.

Each of the contacts RS1, RS2, RS3 are part of a rotary switch 13 having contacts 14, 15, 16, 17 which are spaced at 90° with respect to an adjacent contact.

The rotary switch 13 is provided with contact brushes 18, 19 and is mounted on an axle 20 which is the same or common with the axle of the rotor 11.

Each of the contacts 14, 15, 16, 17 is specially configured with a trapezoidal shape, with the two non-parallel sides consisting of a straight side 21, and a tapered side 22 which tapers outwardly from top side 23 to bottom side 24.

The result is that each contact increases in width from the top side to the bottom side 24.

The brush 18 is able to be moved vertically relative to the contacts 14, 15, 16, 17 while the brush 19 is in constant contact with the base.

Although Figure 1 only shows the rotary switch 13 having a single series of four contacts 14, 15, 16, 17, for the three coil stator system, shown in Figure 4a there would in fact be preferably the contact discs on the axle 20.

Each contact disc would have contacts for a respective one of the coils A, B, C, but each brush for the other discs would be offset by 30° and 60° respectively.

A description of the operation of the system shown in Figures 1 to 4a will now be set forth below.

If it is assumed that the magnets M1, M2, M3, M4 are initially aligned as shown in Figure 4a with magnet M1 opposite one end of coil A, coil A is energized whenever one of the magnets M1 to M4 is aligned opposite it and for a predetermined time after the permanent magnet has passed it.

As shown in Figure 6 coil A is energized by contact RS1 providing an electrical connection through the rotary switch 13.

This occurs by one of the contacts 14 to 17 being aligned in contact with brush 18. At this time current is applied from the power source VA and continues to be applied until the brush 18 is no longer in contact with one of the contacts 14 to 17.

For the three coil/four pole arrangement of the first embodiment it is preferred that the brushes are moved to a vertical position where the width of each contact is sufficient for each of the switches RS1, RS2 and RS3 to be closed for 12°, 51', 50" of the rotation of the rotor 11. After this time the switches RS1 to RS3 are open and no more current is delivered to any one of the coils A to C. When the current to each of the coils is switched off a back EMF is induced in each of the coils A to C and this back EMF represented by item Z results in current being maintained in each of the coils for an additional small period of time after the contacts RS1 to RS3 are opened.

By switching the coils A to C in the above manner the rotor 11 can be induced to rotate with a lower amount of input current to the stator than would be required if current was delivered constantly to the coils A to C.

Table 1 below shows the resultant force on the rotor 13 for angular positions of the magnets M1 to M4 for angular displacements of magnet from 5° to 30°.

Table 1 ~

M1 5° CC 10° CC 15° CC 20° CC 25° CC 30° CC
M2 25° CW 20° CW 15° CW 10° CW 5° CW 0° CW
M3 55° CW 50° CW 45° CW 40° CW 35° CW 30° CW
M4 35° CC 40° CC 45° CC 50° CC 55° CC 60°

As shown when the magnets of the rotor 13 are rotated 5° at a time the resultant force on the rotor changes from a counterclockwise force from 5° to 15° to a clockwise force from 15° to 30°.

At 0°, 15° and 30° the resultant force on the rotor is 0 so that if the permanent magnets of the rotor were aligned in any of these orientation there would be no resultant force to urge the rotor either clockwise or anticlockwise.

As shown in Figure 5 a plot of magnitude of resultant force applied to the rotor against angular displacement of the rotor shows a sinusoidal curve having a cycle of 30°.

For a full 360° rotation of the rotor the rotor would experience 12 cycles of variation in resultant force.

What Table 1 and Figure 5 shows is that unless an additional force is applied to rotate the rotor clockwise or anticlockwise the rotor will not be able to spin continuously in either direction.

If it is assumed that it is desired to rotate the rotor clockwise, then the force must overcome the counterclockwise resultant force which occurs from 0° to 15°, 30° to 45°, 60° to 75°, etc., through the whole 360° rotation of the rotor.

Because each of the coils A to C has an iron core even when the coils are unenergized the natural magnetic attraction occurring between each magnet and the iron cores results in each magnet M1 to M4 attempting to move in a direction to the closest iron core.

Whenever a magnet is opposite an iron core the magnetic attraction is greatest and there is no force applied by that magnet to move the rotor either clockwise or counterclockwise. Likewise when a magnet is positioned midway between adjacent iron cores, there is also a resultant force of 0 which translates to no resultant force being applied to the rotor to rotate it in either direction by that magnet.

As shown in Figure 5 and Table 1, if magnet M1 is moved clockwise 5° there is a natural attraction between the magnet M1 and the iron core of coil A to pull the magnet M1 in a counter clockwise direction. If the resultant forces applied by the other magnets were sufficient to overcome the attraction between permanent magnet M1 and the iron core of coil A the rotor would still manage to move clockwise.

However as shown in Table 1 the angular position of the other magnets M2 to M4 results in an overall counterclockwise resultant force.

To overcome the resultant force it is necessary to produce a pole X at coil A of like polarity to magnet M1 and thus repel M1 away from coil A.

As shown in Figure 5 the strength of the magnetic repelling action between coil A and M1 must be sufficient to overcome the resultant force urging the rotor counterclockwise.

A current could be applied to the coil A for an angular displacement of 15° of magnet M1, but it is preferred that coil A be energized for only 12°, 51', 50" angular displacement of magnet M1. By applying current to coil A for this period of angular displacement a minimum amount of current is applied to coil A in order to overcome the resultant force counterclockwise which occurs for 0° to 15° of angular displacement of magnet M1.

Although current to coil A can be applied for longer than this period it has been discovered that by applying current for this period a back EMF is induced in coil A which adds to the repulsive force applied to magnet M1 by coil A.

Every time one of the magnets M1 to M4 is aligned at 0° with coil A, coil A is energized for 12°, 51', 50" of angular displacement of that magnet. Thus as shown in Figure 6 current ends up being applied to coil A at 0 degrees to 12°, 51 ', 50", 90° to 102°, 51', 50", 180° to 192°, 51', 50" and 270° to 282°, 51', 50".

A similar switching pattern is applied to coils B and C. For example, coil B is energized when magnet M2 has moved 30° to when it has moved 42°, 51', 50" and likewise coil C is energized when magnet M3 has moved 60° to 72°, 51', 50".

It is preferred that the rotor has a diameter of 230 mm and that each coil has a resistance of 6.8 ohms.

Figure 7 shows a graphical representation of input voltage versus input current for a coil resistance of 6.8 ohms and for a four pole rotor which is 230 mm in diameter.

The exact timing sequence for switching coils on and off will vary depending on the parameters of the rotary device and the controller.

Accordingly by varying the input voltage, coil resistance and overall impedance of the input circuit for each coil the duration during which a coil must be turned on will change.

In fact there are many factors which can change the timing sequence of switching on the coils, and some of these are summarized below.

The Stator

The variables include the choice of material used in constructing the stator iron core, the number of stator iron cores and their positioning as well as the physical size, section area and shape of the stator iron cores.

Rotor

The physical size and magnetic strength and shape of the polarized permanent magnetic body as contained in the rotor, the number of polarized permanent magnetized bodies being contained in the rotor, the positioning and spacing of the same, the use of all like polarities of permanent magnetic bodies or the use of alternating polarities for the permanent magnetic bodies.

Stator Coil

The physical size of the coils being positioned onto the stator iron core(s), the type of wire used to wind the coils(s) such as copper, silver, aluminum or others. The shape and section areas of the winding wire, such as round, square, triangular, rectangular and others; the number of turns and layers wound onto the coil and consequent ohms resistance; the method of winding onto a coil holder, single winding, double winding, double winding same direction, double winding opposite direction, left to right and vice versa, interwoven winding, whether the above examples would be wound onto a single coil holder.

Speed of Rotor

This can be controlled by the length of the directed (input) DC current (on and cut off period) and/or the control of the supply voltage used to supply the stator coils(s).

Other variations that may be made to the system include the following:

(a) The coils can be connected in series, parallel or series parallel.

(b) It is only when the north/south arrangements of the permanent magnets are used in the rotor that even numbers of permanent magnets are necessary, but not necessarily even numbers of pairs of stator coils positioned in the stator. Furthermore the direction DC current supplied to the stator coils in the north south arrangement above must be synchronized, meaning that the magnetic field as needed in the stator coil(s) must be of corresponding polarity to the stator coil(s), iron core end, which faces the permanent magnets.

(c) When using permanent magnets which are all of the same polarity, then any number of permanent magnets in the rotor may be used providing there is sufficient room to contain them, at even spacings on the rotor.

(d) The spacings between the permanent magnets must be exact; if too close to each other the directed DC current will become less effective; if too far apart the full potential will not be obtained.

(e) It is possible to have various combinations of permanent magnet and stator coil iron cores similar but not restricted to the following:

(i) Three magnets in the rotor, one to three stator coils can be used.

(ii) Five permanent magnets in the rotor, one to five stator coils can be used.

(iii) Nine permanent magnets in the rotor, one to three or nine stator coils can be used.

(iv) The output varies with each combination.

(v) Regardless of the rotor containing even or uneven numbers of permanent magnets the stator can operate with only one stator coil and stator iron core and still be highly effective but with reduced total output.

(f) The stator and rotor should be made from non-magnetic materials like wood, plastic, bronze and similar non-magnetic materials.

Although switching is performed in its preferred form by a mechanical rotary switch, it can also be performed by solid state electronics or other switching devices.

The length of the on period for each coil is the physical length ratio. When the brushes are in contact with the conductive part of the rotary switch and the non-conductive part.

This ratio is referred to as the frequency or number of ratios in one second.

The output produced by the rotary device can be mechanical and electrical at the same time or may be mainly electrical or mainly mechanical. The reason for this will be explained with reference to the second embodiment in which it is assumed the stator has a single energizing coil with an iron core and the rotor has a single permanent magnet.

When the rotor's permanent magnet is rotated very slowly by hand in the clockwise direction it is possible to determine the point where the natural magnetic attraction between the rotor's permanent magnet and the stator's iron core occurs.

When the leading edge of the permanent magnet has reached a point A as shown in Figure 8, the natural magnetic attraction begins and increases exponentially until the center of the permanent magnet is aligned at point B opposite the iron core 30.

If the permanent magnet is rotated away from point B the NMA will be at a maximum point B and then decrease from maximum exponentially until the trailing edge of the permanent magnet has reached point C and then ceases.

When the rotor is moved clockwise at a constant speed and an oscilloscope is connected to the stator coil it is possible to observe the movement of the permanent magnetic between point A and point B and then between point B and point C as shown in Figure 9.

An induced induction curve is then apparent on the oscilloscope and this induced induction produces a sine wave curve 31. Furthermore the induced induction between point A to point B is a negative going induced induction in this instance and the induced induction between point B and point C is a positive going induced induction in this instant.

It is also noted that the negative going and positive going induced induction curves are exactly the same but opposite to each other.

When the permanent magnet begins to induce a negative going induction in the stator coil at 0° of the sine wave curve 31, the induction induced is then at 0. At 90° of the sine wave curve the induced induction is at a maximum and then goes back to 0 when the permanent magnet is aligned with point B, or at 180° of the sine wave curve, when the permanent magnet starts to move away from its alignment with point B or is at 180° of the sine wave curve.

When the permanent magnet starts to move away from its alignment with point B and is moving towards point C the now positive going induced induction is first at 0 at 180° of the sine wave curve, then at a maximum of 270° of the reached point A as shown in Figure 8, the natural magnetic attraction begins and increases exponentially until the center of the permanent magnet is aligned at point B opposite the iron core 30.

If the permanent magnet is rotated away from point B the NMA will be at a maximum point at point B and then decrease from maximum exponentially until the trailing edge of the permanent magnet has reached point C and then ceases.

When the rotor is moved clockwise at a constant speed and an oscilloscope is connected to the stator coil it is possible to observe the moment of the permanent magnetic between point A and point B and then between point B and point C as shown in Figure 9.

An induced induction curve is then apparent on the oscilloscope and this induced induction produces a sine wave curve 31. Furthermore the induced induction between point A to point B is a negative going induced induction in this instance and the induced induction between point B and point C is a positive going induced induction in this instant.

It is also noted that the negative going and positive going induced induction curves are exactly the same but opposite to each other.

When the permanent magnet begins to induce a negative going induction in the stator coil at 0° of the sine wave curve 31, the induction induced is then at 0. At 90° of the sine wave the induced induction is at a maximum and then goes back to 0 when the permanent magnet is aligned with point B, or at 180° of the sine wave curve, when the permanent magnet starts to move away from its alignment with point B or is at 180° of the sine wave curve.

When the permanent magnets start to move away from its alignment with point B and is moving towards point C the now positive going induced induction is first at 0 at 180° of the sine wave curve, then at a maximum of 270° of the sine wave curve and then back to 0 at 360° of the sine wave curve.

It should be noted that 0° and 360° of the sine wave curve are not necessarily the same as point A for 0° and point C for 360° of the sine wave curve.

Points A and C are determined by the strength of the rotors permanent magnet and the section area and/or shape of the stator iron core.

The negative going induced induction between 0° and 180° of the sine wave curve produces an electro-magnetic force in the stator coil and iron core of opposite polarity.

The iron core end facing the rotor is of opposite polarity than the permanent magnet in this instance, as shown in Figure 10.

The positive going induced induction between 180° and 360° of the sine wave curve produces an electro-magnetic force in the stator coil and iron core of the same polarity in the iron core end facing the rotor, being of the same polarity as the permanent magnet in this instance.

When the permanent magnet reaches point A the natural magnetic attraction between the permanent magnet and the stator iron core is at its minimum and starts to move towards point B. When the induced induction then also starts to occur at 0° of the sine wave curve, being somewhere between point A and point B, the natural magnetic attraction has already increased.

When the permanent magnet is at 0° of the sine wave curve and is moving towards point B or 180° of the sine wave curve, the negative going induced induction in the stator coil is producing an electro-magnetic force (field) in the stator iron core with the iron core end facing the rotor being of an opposite polarity than the permanent magnet and is at zero effect at 0° of the sine wave curve, than at maximum effect at 90° of the sine wave curve and then back to zero effect at 180° of the sine wave curve.

The permanent magnet is then aligned at point B.

There the magnetic attraction force is proportional with the distance and this increases exponentially when moving from point A toward point B. There the iron core is fixed and stationary at point B. Accordingly it will be the permanent magnet that moves towards point B.

As an example, if the stator iron core was also a polarized permanent magnetic body of the same strength but of opposite polarity to the permanent magnet, the magnetic attraction force would be at least four times greater because of the distance factor as explained earlier.

Furthermore, this would also occur because of the doubling of the magnetic force between the magnetic north and south arrangement. It follows therefore that the magnetic attraction between the permanent magnet and the iron core and facing the rotor increases dramatically when the induced induction in the stator coil produces an electro-magnetic force of opposite polarity at the stator iron core end facing the rotor as described above.

The increase follows the sine wave curve starting from 0° to 90° of the sine wave and the above effect decreases from 90° back to 180° of the sine wave curve.

A combination curve of the natural magnetic attraction an the induced induction in the stator coil, producing an electro-magnetic force at the stator iron coil end facing the rotor of opposite polarity 33 is shown in Figure 10 from 0° to 180°. For 180° to 360° the stator iron coil and rotor of like polarities 34 are shown.

When the permanent magnet is aligned at point B and a direct current is supplied to the stator coil for only a short period starting at point B then the DC current is applied only long enough to overcome the natural magnetic attraction between the permanent magnet and the stator's iron core end facing the rotor. The directed DC current as supplied to the stator's coil is producing a like-polarity at the iron core end facing the rotor and thus is repelling the permanent magnet away from point B towards point C.

The natural magnetic attraction has thus changed to natural magnetic repulsion due to the like-polarity of the stator iron core end facing the rotor.

The length of the "on" period has to be sufficient to overcome the natural magnetic attraction and could be as long as until the trailing edge reaches point C where the natural magnetic attraction ceases. However there the positive going induced induction in the stator coil as produced by the permanent magnet produces an electro-magnetic force in the stator or iron core end facing the rotor, producing a like polarity as the permanent magnet starting at 180° of the sine wave curve or point B and zero at that instant. At 270° of the sine wave curve, it is at a maximum and then ends up at zero at 360° of the sine wave curve. In other words, at 270° of the sine wave the force is at maximum repulsion and there is induced induction in the stator coil depending on the speed of the rotor. The effect of variation on the speed of the rotor is shown by curves 35 in Figure 11.

As shown in Figure 11, regardless of the speed of the rotor the induced induction in the stator coil is at a maximum at 270° of the sine wave curve.

The on period can be brought back to the point where the induced induction is great enough to carry the electro-magnetic repulsion through to 360° of the sine wave curve and beyond point C. Therefore the greater the rotor speed the shorter the on period of the input DC current has to be due to the high induced induction in the stator coil as explained earlier. When the "on" period is switched off it is called the 'cut-off" point. From the cut-off point to 360° of the sine wave curve the repulsion is produced by back EMF, the induced induction in the stator coil as previously explained.

During the on period, the magnetic repulsion force produced between the stator iron core at point B and the permanent magnet can be viewed as a combined repulsion force. Some of this force is produced by natural magnetic repulsion of the permanent magnet and some by the input DC natural magnetic repulsion due to the like-polarity of the stator iron core end facing the rotor.

The length of the "on" natural magnetic repulsion due to the like-polarity of the stator iron core end facing the rotor.

The length of the "on" period has to be sufficient to overcome the natural magnetic attraction and could be as long as until the trailing edge reaches point C where the natural magnetic attraction ceases. However there the positive going induced induction in the stator coil as produced by the permanent magnet produces an electromagnetic force in the stator or iron core end facing the rotor, producing a like polarity as the permanent magnet starting at 180° of the sine wave curve or point B and zero at that instant. At 270° of the sine wave curve, it is at a maximum and then ends up at zero at 360° of the sine wave curve. In other words, at 270° of the sine wave curve, it is at a maximum and then ends up at zero at 360° of the sine wave curve. In other words, at 270° of the sine wave the force is at maximum repulsion and there is induced induction in the stator coil depending on the speed of the rotor. The effect of variation on the speed of the rotor is shown by curves 35 at Figure 11.

As shown in Figure 11, regardless of the speed of the rotor the induced induction in the stator coil is at a maximum at 270° of the sine wave curve.

The on period can be brought back to the point where the induced induction is great enough to carry the electro-magnetic repulsion through to 360° of the sine wave curve and beyond point C. therefore the greater the rotor speed the shorter the on period of the input DC current has to be due to the high induced induction in the stator coil as explained earlier. When the "on" period is switched off it is called the "cut-off" point. From the cut-off point to 360° of the sine wave curve the repulsion is produced by back EMF, the induced induction in the stator coil as previously explained.

During the on period, the magnetic repulsion force produced between the stator iron core at point B and the permanent magnet can be viewed as a combined repulsion force. Some of this force is produced by natural magnetic repulsion of the permanent magnet and some by the input DC current as supplied to the stator coil. Therefore if the induced magnetic force as produced by the input DC current in the stator coil is made equal to that of the permanent magnet with the same polarity, then half of this repulsion force between the on period and the cut-off point, in this instance, is from the natural magnetic repulsion of the permanent magnet as a reaction to the induced magnetic force as supplied by the input DC current to the stator coil. Therefore if the induced magnetic force as produced by the input DC current in the stator coil is made equal to that of the permanent magnet with the same polarity, then half of this repulsion force between the on period and the cut-off point, in this instance, is from the natural magnetic repulsion of the permanent magnet as a reaction to the induced magnetic force as supplied by the input DC current to the stator coil.

The input DC current as supplied to the stator coil produces the magnetic repulsion force and is the only outside input to the overall system for total movement between point A and point C

The total input can be summarized as:

(a) The combined natural magnetic attraction and the electro-magnetic force as produced by the induced induction in the stator coil between point A to point B.

(b) The combined magnetic repulsion force between the permanent magnet and the stator iron core facing the rotor during the on period and the cut-off point.

(c) The electro-magnetic repulsion (see induced induction as explained earlier) between the cut-off point and point C.

(d) The electro-magnetic repulsion produced by the back EMF as represented by shaded portion 36 of Figure 11.

According to another embodiment of the present invention the stator has two coils positioned at 180° with respect to each other and the rotor has three permanent magnets spaced at 120° apart.

As set out in Table 2 below from 0° to 30° the resultant force is 0 and from 30° to 90° the resultant force is clockwise. From 90° to 120° the resultant force is counter-clockwise. This completes a full cycle which is repeated three times throughout a 360° rotation of the rotor.

Table 2 ~

M1 5° CC 10° CC 15° CC 20° CC 25° CC 30° CC
M2 55° CW 50° CW 45° CW 40° CW 35° CW 30° CW
M3 65° CC 70° CC 75° CC 80° CC 85° CC 90°
RF CC CC CC CC CC 0°

With the above configuration of poles and coils if it is desired to move the rotor clockwise, current would need to be supplied to the coils of the stator to overcome the counter-clockwise force whenever this is counter-clockwise, but as explained previously, current does not need to be supplied to the coil to energize the coil for the full period during which the resultant force is counter-clockwise.

For convenience and ease of explanation the above embodiments have been restricted to permanent magnets on the rotor and coils on the stator. However the basic concept behind the invention does not change if the permanent magnets are replaced by coils which are energized to produce the appropriate magnetic poles.

Similarly for an AC rotary device a rotating magnetic field generated by the stator winding or by the rotor/armature winding could similarly be switched to reduce the amount of current required to maintain rotation of the motor in one direction and to maximize the influence of back EMF on maintaining rotation of the motor in a single direction.

The above principles also apply to generators where coils are energized to produce a magnetic field. In such a situation the coils are switched on for a time sufficient to maintain rotation in the single direction and to maximize the influence of back EMF which tends to maintain rotation of the rotor/armature in a single direction.

By using the above concept it is possible to produce an output which can be both mechanical and electrical at the same time. Current generated in the stator coil windings can be used as an output and likewise the torque generated by the rotor can be used to supply a mechanical output. Likewise only one or the other form of output may be utilized.

Adams vs Lutec

Alternative Energy Institute (July 17, 2002) ~ www.altenergy.org/news/newsletter79/copy79/copy79.html

Adams' Invention Poached Down Under

According to a recent article published by an Australian newspaper, two Australian inventors have developed the world's "first commercial machine which can power a house from a clean, green virtually free energy source." The story has been posted on the Aethmogen Technologies: New Energy Scientists website "for those interested in the subject of reverse engineering, plagiarism, and stolen intellectual and other property." In response to the anticipated production of the "Lutec 1000 Motor/Generator," noted Australian inventor Dr. Robert Adams reports background details to enforce his argument that this magnetic motor cannot be patented. Adam's writes, "This invention, which is mine, was granted a British Patent in 1996 along with Dr. Harold Aspden of the United Kingdom (IBM's Patent Director for 19 years), was placed in the public domain by international publication in Nexus Magazine and according to International Patent law, thenceforth becomes unpatentable!" Learn more about this unfolding drama from Down Under.

Rosenthal's Measurements: Negative Result Reports

Engineers Reporting Negative Results: Rosenthal and Cole ~ Ian Bryce
Report by Sterling D. Allan (March 8, 2003)

Engineers, Walt Rosenthal and Parke Cole were invited to measure the Lutec1000 in January 2001. Their measurements showed results showed 28% efficiency. The exchange was amendable, despite the negative test results. Rosenthal stated, "I walked them through the calculations carefully so they would understand, but they didn't want to believe the results." Test entailed a dynamometer measuring output the motor, powering with power supply from wall producing DC volts, optical shaft encoder on end of shaft to measure rpm. Results showed 50 Watts power going in and 14 Watts equivalent of mechanical power coming out.

After receiving the above synopsis, Walt Rosenthal added the following:

Report by Walt Rosenthal (March 8, 2003) ~

The inventors would start with fully charged batteries for the demonstration. They assumed that the battery terminal voltage would decrease linearly as the battery was used. So, after using the battery for, say, 30 minutes, they would again measure the battery terminal voltage, and subtract this value from the start voltage, then multiply that difference voltage times the known amp-hour capacity of the battery bank, to come up with their assumption of the total energy consumed from the battery bank. Unfortunately, battery terminal voltage is almost flat for perhaps 90 percent of the battery capacity, before it drops off rather steeply for the last 10 percent of it's capacity. Parke Cole and I tried to explain this to the inventors. I am not sure we succeeded. We were about the 15th group of people to show up on their door step after they went public. We were the first people to bring our own test equipment. The inventors said that the first people to show up were the Russian Mafia. Our bottom line was 50 watts of DC power input, which resulted in 14 watts of rotary mechanical power output. I hope the inventors have improved their device from where we tested it so that it now matches their statements of it's performance.

Follow-up Comment from Walt ~

From: Walter Rosenthal ~ To: sterlingda@greaterthings.com (March 15, 2003)
Subject: Energy Wise 1000 mentioned at GreaterThings.com

Sterling: The pictures of the Lutec 1000 show that the inventors have added a second unit apparently driven by the motor and in line with the motor since Parke and I tested it... Walt

Feedback From Scott MacGregor ~

To: Sterling D. Allan (March 09, 2003)
Subject: Lutek 1000 only 28% efficient according to Rosenthal, 2001 independent measurement

Thanks for that update. It seems evident that although electro-magnets require energy input to "turn on", permanent magnets require energy input to "turn off"! The example given on their Website - the permanent magnet and electro-magnet supporting a weight from a steel beam - should demonstrate this principle. i.e., Energy must be inputted to the electro-magnet in order to overcome the weight. Although no external energy is required for the permanent magnet to support the weight, energy must be supplied to OVERCOME the magnet and cause the weight to fall...thereby producing useful energy. In other words, the permanent magnet is producing zero energy while supporting the weight.

Email from Patrick Bailey:

From: Bailey, Patrick
February 20, 2008
RE: Zero Point Energy Machine from Australia - Lutec

...Walter Rosenthal traveled there with his high frequency digital oscilloscope and measured the devices.

IT IS THE SAME OLD LYING GAME!

People are measuring high freq. DC or fast pulsating AC with AC meters calibrated to sine wave 0.707 RMS.

You can not do that!

Using just AC meters (like an old VTVM), I could easily show you that a resistor, capacitor, and inductor arrangement will always give you over unity! (Just by ignoring the current to voltage phase angle.)

Walter measured the voltage vs. time digitally (storing many data points per cycle), and the current vs. time digitally, and then calculated the power point by point via computer, and then calculated the average power digitally - for input power and output power.

Then you can get the True output to input power ratio.

You must use a high frequency oscilloscope with such computing abilities!!!

Go to this webpage to see photos and technical diagrams: http://www.rexresearch.com/christie/christie.htm

-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

CONTACT US: http://www.lutec.com.au/contact.htm
HOW IT WORKS: http://www.lutec.com.au/how.htm
TECHNICAL DATA: http://www.lutec.com.au/tech.htm
APPLICATIONS: http://www.lutec.com.au/buttons/button15.jpg
L.E.A: http://www.lutec.com.au/buttons/button13.jpg
ENVIRONMENT: http://www.lutec.com.au/enviro.htm
PATENTS: http://www.lutec.com.au/patents.htm
OPPORTUNITIES: http://www.lutec.com.au/invest.htm
HEROES: http://www.lutec.com.au/heroes.htm
HOME PAGE: http://www.lutec.com.au/index.htm

Support The Love For Life Campaign, Kindom & The Cristian Family

Supporting The Love For Life Website, The Cristian Family and The Living Dream Of Kindom (Creation Of Do No Harm Communities) - The Love for Life website is produced for free without a fee (no contract or conditions attached) as a gift of love for the benefit of others. If you feel you have gained something from visiting it, feel inspired, and would like to reciprocate as an equal exchange in substance and support (value), you are most welcome to make a gift of love to keep it and the dream of Kindom going. As always, we thank you for your gifts of love.

Additional Options

Bank:
Account name:
BSB:
Account number:
SWIFT BIC Code:
Australia New Zealand Banking Group (ANZ)
Fiona Caroline Cristian
012 547
5576 81376
ANZBAU3M

PAY PAL

Go To Your Pay Pal Account To Send Gifts To action @ loveforlife.com.au
Additional Options

 

The Cristian Family November 2006

We Stand For NO SYSTEM

Kindom (Do No Harm Communities) is the dream for freedom, but it is the dream for the freedom of those around us who also live the dream of freedom, because it is in living for the freedom of others that we get our freedom. When we live for the dreams of Kindom of those around us, we live life as a gift because we live for (dedicate our lives to) their dream of freedom, truth, peace, joy, abundance, etc, just as they live for our Kindom dreams too. This is true co-creation (cooperation) with no attack on the uniqueness of each of us. When we live this way, we have no need for any man-made system - everything/everyone has already been taken care of by our love for life.

Just as we do not have to jump 10 feet across the room to grab our next breath, neither do we have to worry about food, water and shelter because it has all been taken care of as we each co-create Kindoms/Kin-Domains for everyone. Now everybody and everything of the dream of life that is Kindom/Paradise is free (has been set free once again). The issue is greed and selfishness, power and control trips, arrogance, ignorance, being fed many many lies and being traumatised. The issue is not overpopulation - there is more than enough land available for every family to have a hectare (2.5 acres Kin-Domain) to care for. The land of Australia can provide a Kin-Domain for every family across Earth, each with a food forest, clean fresh drinking water and plenty of space for building natural do no harm habitats and with plenty of land left over.

Everyone must have the freedom to take full-responsibility for their lives, for the water they drink, the food they eat and for their shelter. Currently, "The System" forces everyone to give up taking full-responsibility so that we become grown up children accustomed to sucking on the nipples of "The System" corporations for everything, having to use money to get by and to follow the rules of money because we are not co-creating freedom, peace, truth, joy and abundance for each other. Money only leads to haves and have nots and all the abuse, manipulation and distractions that we are subjected to as slaves to money.

When we give up living for other's Kindom dreams, we start creating hell ("The System") all around us because we become self-centred - now it's all about "my freedom","my money", "my land", "my belief", "my saviour", "mine", "mine","mine", "i","i", "i", "own", "own", "own", etc. To protect what we claim we own requires a man-made system with FORCE to protect those self-centred claims. This is ALL trauma based and all story-telling (brainwashing/braindirtying).

NO SYSTEM = KINDOM/DO NO HARM COMMUNITIES
NO SYSTEM = KINDOM/DO NO HARM COMMUNITIES photo Kindom_zpsa6d24e8a.jpg

Our true freedom comes when we set our thoughts of freedom into motion so that we live freedom rather than just talking and thinking about it while we still slave for "The System". Kindom will not happen while we meditate for hours in the bush or do yoga retreats or wait for Jesus or follow the processes of the OPPT (One People's Public Trust now called One People). This is not freedom because we are not living freedom because we are living the story-telling of Jesus or Zeitgeist or The Secret or Thrive or One Earth/Consciousness/People.

Living Kindom is very, very hard work as we set about repairing the damage to MAN/Earth/Nature that we are ALL responsible for but the burden becomes lighter the more of us put our life-energy into the dream of returning Earth to Paradise. Day-after-day, we all have to work our arses off until Kindom is all around us (MAN) once again. This is the price we pay to set each other free on a piece of land (Kin-Domain), so that no one is under the image-power (education/brainwashing/story-telling) of another MAN anymore and so that everyone can have their space of love to create and live their unique, do no harm dreams. This only happens once we have the Kindoms set up so that everyone is provided for.

Once we re-create the food forests, whether on land or in the suburbs, we can re-claim our freedom, breaking the strangle-hold of "The System" because we are no longer reliant on its services and benefits and no longer turning each other into slaves of "The System", cogs in the wheels of "The System" machine. If we don't put the effort in to set everyone and everything free all around us then we still live in HELL ("The System"). The key is to live for everyone else's freedom so that we can have it too.

From Bare Dirt To Abundance
A Year In The Life Of The
Love For Life Food Forest

Arthur & Fiona Cristian
8th February 2013
51 Minutes 46 Seconds
http://www.youtube.com/watch?v=1sJCcCvZ97A

We live for NO SYSTEM. We do not lose anything by not having a man-made system and, in fact, we gain. We gain our freedom and we gain abundance. Let go of the fear.

The Cristian Family November 2006

A Collection Of Various Love For Life Posts
Providing The Big Picture We See

Sequential Order

We ask you to NOT believe anything we say/share and instead use scrutiny like an intense blow torch and go where the logic of truth/sense takes you. This is very, very important. Put everything you believe up to the test of scrutiny to see how it stacks up. If you are true to your heart/senses and go where the logic of truth/sense takes you will find that NO belief, etc, will stand up to the test of scrutiny. They just do not stack up because they are lies/fraud.

After you have watched and read all the material and any questions are left unanswered, send us your landline number and we will use the internet phone as a free unlimited call. We are on Sydney NSW Australia time. Best times for us to chat are between 11.00am and 6.00pm.

It is critical that you fully comprehend Image Power, "Spelling", Trauma, Reaction To Trauma, Curses, Processing Curses, Full-Responsibility/Liability, Limited Liability/Responsibility (passing-the-back), Slavery, Senses/Sense vs Non-Sense/Senses, Re-Presenting Intellectual Property such as but not limited to "Name", Storytelling/Storytellers, Duality, Black-Magic, Belief, Lies, "i", All Seeing "i" (eye), etc..... These themes and others are covered over and over and over again.

If you do not comprehend these insights and are unable to use your senses to sense your way through all the non-sense/non-sensory-images that enslave MAN under their image power (darkness = "The System" = Hell), men and women will remain deeply trapped under a terrible state of trauma. Our intention is to inspire you to remedy by showing you how to move away from reacting to trauma in all its nefarious and devious forms.

His-Story/Her-Story (History)
Arthur Cristian - Love For Life
2005-2007 - Re-posted July 2014
http://loveforlife.com.au/node/8529

The Dream Of Life Part 6
Under The Spell Of Intellectual Property

Arthur Cristian - 51 Minutes 52 Seconds
http://www.youtube.com/watch?v=IMK7CkU1ih8

The "Name" Is The Mark Of The Beast
The Strawman Identifying
Your Slave Status In "The System"

By Arthur Cristian - Love For Life
5th February 2012 - 56 Minutes 25 Seconds
http://www.youtube.com/watch?v=DdOag66v7uo

IMAGE POWER
The Nefarious Tactics Used
To Disguise Truth And Distract Us
From Remedy

Arthur & Fiona Cristian
Love For Life
24th January 2014
This post contains many recent Facebook comments
and email replies which collectively provides a big picture
into exposing the deception behind IMAGE POWER.
http://loveforlife.com.au/node/8496

The Pull Of E-Motion
Arthur & Fiona Cristian
Love For Life
8th February 2014
http://loveforlife.com.au/node/8499

IMAGE POWER
Superb Diamond Range Interviewing
Arthur & Fiona Cristian 4th February 2014
http://youtu.be/qFnuuw3kLog
http://loveforlife.com.au/node/8501

Trauma Induced Fantasy
July 2013 Interview With
Jeanice Barcelo And Arthur & Fiona Cristian
http://youtu.be/CZVj-ddUoZw
http://loveforlife.com.au/node/8500

Processing Curses
A Lie Is A Curse
Liars Process Curses

Arthur & Fiona Cristian
Love For Life
26th February 2014
http://loveforlife.com.au/node/8503

How The System Is Really Constructed
Bouncing Back Curses Upon Curse Makers
To Stop Harm Forevermore

Arthur & Fiona Cristian
Love For Life
27th February 2014
http://loveforlife.com.au/node/8504

Slave To A Name
Parts One, Two, Three, Four,
Arthur & Fiona Cristian
Love For Life
3rd to 6th March 2014
http://loveforlife.com.au/node/8505

Educated Slaves
Arthur & Fiona Cristian
Love For Life
20th March 2014
http://loveforlife.com.au/node/8506

The Only Path To Freedom
Beware The False Steps

Arthur & Fiona Cristian
Love For Life - 2nd April 2014
http://loveforlife.com.au/node/8508

Free-Dumb For All
Arthur & Fiona Cristian
Love For Life - 5th April 2014
http://loveforlife.com.au/node/8510

Revoking The Ego
Arthur & Fiona Cristian
Love For Life - 8th April 2014
http://loveforlife.com.au/node/8511

How MAN Commits Spiritual Suicide
Arthur Cristian
Love For Life - 3rd April 2014
http://loveforlife.com.au/node/8509

How To Detect Intel Operatives Working
For The New World Order Agenda
Arthur & Fiona Cristian
Love For Life - 10th April 2014
http://loveforlife.com.au/node/8512

How The Psyop Program & Intel Networks
Are Messing With Your Head +
His-Story/Her-Story

Arthur & Fiona Cristian - April 2014
http://loveforlife.com.au/node/8513

Godzilla Through The Looking Glass
Destroyed By Name"

Arthur & Fiona Cristian
Love For Life - 20th April 2014
http://loveforlife.com.au/node/8514

What It's Going To Take
To Co-Create Freedom Forevermore

Arthur & Fiona Cristian
Love For Life - 22nd April 2014
http://loveforlife.com.au/node/8514

Falling For Fairy Stories
Arthur & Fiona Cristian
Love For Life - 24th April 2014
http://loveforlife.com.au/node/8514

A Disassociation From The Work
Of Kate of Gaia

Arthur & Fiona Cristian
Love For Life - 17th May 2014
http://loveforlife.com.au/node/8517

Separating The Wheat From The Chaff
Arthur & Fiona Cristian
Love For Life - 22nd May 2014
http://loveforlife.com.au/node/8516

Revolution Or Revolution
Arthur & Fiona Cristian
Love For Life - 25th May 2014
http://loveforlife.com.au/node/8520

Routing Out Psyop Programs
Routs Out Intel Operatives
Exposing Max Igan's Psyop Program

Arthur & Fiona Cristian
Love For Life - 31st May 2014
http://loveforlife.com.au/node/8524

The Psyop Program Scam
Behind Religion Belief Faith
& Associated Opinion

Arthur Cristian
Love For Life
11th June 2014
http://loveforlife.com.au/node/8525

Another Delusion
Arthur Cristian
Love For Life
11th June 2014
http://loveforlife.com.au/node/8526

A World Of Words Is A World Of Lies
Arthur Cristian
Love For Life
13th June 2014
http://loveforlife.com.au/node/8527

E-MAN
The Name Of The Beast Is MAN

Arthur & Fiona Cristian
Love For Life - 9th May 2014
Includes Mountain MAN Arrested
Facebook Discussion About "Name"
Uploaded 25th June 2014
http://loveforlife.com.au/node/8528

Crop Circles Are A Massive Hoax
Facebook Discussion On Simon Kawai's Wall
Involving Arthur & Fiona Cristian
31st August 2013
http://loveforlife.com.au/node/8470

OPPT & Slavery Through Intellectual Conscription By Deceit
Arthur & Fiona Cristian - Love For Life
27th February 2013 onwards...
Part One: http://youtu.be/Qjp_9nlrBao
Part Two: http://youtu.be/tbybeOWZ-Bc
Part Three: http://youtu.be/yOWoxH-HbVw

Water Is The Life Of MANS Consciousness (Breath)
Arthur & Fiona Cristian - Love For Life - 8th February 2013
http://loveforlife.com.au/node/8350
Part One: http://youtu.be/4ze66_33wxM - 70 Minutes 5 Seconds
Part Two: http://youtu.be/43gIi-sjxJc - 81 Minutes 13 Seconds
Part Three: http://youtu.be/oooY6W63K-M - 70 Minutes 18 Seconds

What Do You Believe On Origins?
Who Said There Was A Beginning?
Who's Truth Do You Accept?
Belief Is A Strange Idea.

Discussion Lyndell, Scott and Arthur & Fiona Cristian
Between March and April 2013
Posted 29th October 2013
http://loveforlife.com.au/node/8487

So You Want The Good Bits Of "The System"
But Not The Bad Bits?

By Arthur & Fiona Cristian
Love For Life - 12th August 2013
http://loveforlife.com.au/node/8468

Turning Away From The Reflection
Of MANS Looking Glass

Arthur & Fiona Cristian
Love For Life
30th April 2013
http://loveforlife.com.au/node/8404

REMEDY

From Bare Dirt To Abundance
A Year In The Life Of The
Love For Life Food Forest

Arthur & Fiona Cristian
8th February 2013
51 Minutes 46 Seconds
http://www.youtube.com/watch?v=1sJCcCvZ97A

Control The Land
And You Control MAN On The Land
Displace MAN From Land
And You Turn MAN Into Slaves

Arthur & Fiona Cristian - Love For Life
April 2011 (Updated 14th September 2011)
http://loveforlife.com.au/node/8237

The Divine Spark
Facebook Discussion With Raymond Karczewski
Arthur & Fiona Cristian & Others
2nd October 2013
http://loveforlife.com.au/node/8483

Capturing Another MANS Uniqueness
A Facebook Debate With
Arthur & Fiona Cristian - Love For Life
And Raymond Karczewski
Starting 13th May 2013
http://loveforlife.com.au/node/8414

The Spell Is Broken
Taking The Land To Create Kindom

Arthur & Fiona Cristian
Love For Life
3rd March 2013
http://loveforlife.com.au/node/8365

The Steps Of Kindom
Arthur & Fiona Cristian
Love For Life 2006/2007
http://loveforlife.com.au/node/8304

To explore these themes in greater detail go here where you can find links to all our Love For Life comments, articles, debates, discussions, videos, podcasts, etc: http://loveforlife.com.au/node/3385

All the best
Arthur & Fiona Cristian
Love For Life

Website: http://loveforlife.com.au
Email : action@loveforlife.com.au
Mobile : 0011 61 418 203204 - (0418 203204)
Snail Mail: PO Box 1320 Bowral 2576 NSW Australia
Facebook Arthur Cristian : http://www.facebook.com/arthurcristian
YouTube Arthur Cristian : http://www.youtube.com/ArthurLoveForLife

Register To The Love For Life Mailing List: http://loveforlife.com.au/content/09/05/14/mailing-list

Facebook Group Why Aren't We Free Discussion : http://www.facebook.com/164918753537287
Facebook Group Kindom/Do No Harm Community Discussion : http://www.facebook.com/151811728195925

Links below will kick in when the professionally recorded Love For Life music is released.

SoundCloud : http://soundcloud.com/loveforlife
Nimbit Music : http://www.nimbitmusic.com/loveforlife
Twitter : https://twitter.com/loveforlifemusi
Facebook Music : http://www.facebook.com/loveforlifemusic
YouTube Love For Life Music : http://www.myspace.com/loveforlifemusic
MySpace : http://www.myspace.com/loveforlifemusic
Google + Fiona Cristian : https://plus.google.com/100490175160871610090

Peaceful Transition Through Sacrifice And Service

We feel there is an essential peaceful do no harm transition required to get all of MAN back to standing on MANS feet without reliance upon another MAN for water, food, shelter. As it stands everyone in "The System" are highly dependent and reliant on the "group mind-set" that forms "The System" of slaves providing services and benefits for the emotionally addicted slaves to "The System" (and you can put us in the same basket too). The transition is to get MAN back to relying ONLY on nature without 3rd party interlopers, intermeddlers, interceders getting in the way. The transition is a team effort with the foresight for setting all of MAN free down-the-line so that MAN is no longer dependent on slaves and masters providing services, benefits, privileges and exclusivity while being bound to contracts, rituals, procedures, conditions, rules & regulations which compromises MAN severely.

This transition is all about shifting from limited liability/responsibility to full liability/responsibility. This full responsibility is all about caring for our health, nature all around us, clean uncorrupted (pure) water and food, partner/co-creator, children, shelter, animal-friends in partnership, etc. In "The System", we are already together destroying each other - we have to come together to create peace together so that we can all have peace. We cannot live peacefully when we are islands, not taking full responsibility for the lives of those around us until EVERYONE can take full responsibility for their life, which means that EVERYONE is healed of system trauma. In "The System", we all come together to make slaves of each other - now is the moment to come together to set each other free, to live for each other's freedom, peace, joy and abundance. Once we have set each other free, we are free.

Control The Land
And You Control MAN On The Land
Displace MAN From Land
And You Turn MAN Into Slaves

Arthur & Fiona Cristian - Love For Life
April 2011 (Updated 14th September 2011)
http://loveforlife.com.au/node/8237

The Spell Is Broken
Taking The Land To Create Kindom

Arthur & Fiona Cristian
Love For Life
3rd March 2013
http://loveforlife.com.au/node/8365

"The Steps Of Kindom"
http://loveforlife.com.au/node/8304

---------

Once we fix these issues, we or our children or our descendants to come, can start focusing on the even bigger picture of getting back to where our ancestors were, as breatharyan's, before they fell into non-sense images to be enslaved by them.

All the best to you and your family
Arthur & Fiona Cristian
Love For Life

The Cristian Family November 2006

The Cristian Family Declaration

The Cristian family and The Love for Life Campaign are apolitical, non-religious, non-violent, anti weapons, anti drugs (both pharmaceutical and recreational) and anti any ideology that denies the existence of Do No Harm Communities (Kindoms) and suppresses the uniqueness and freedom of all men, women and children.

The Cristian family and our Love For Life work is unaligned to any big business corporation, intelligence agency, government body, "system" law, "system" think tanks, "system" green or environmental movements, religion, cult, sect, society (fraternity, brotherhood, sisterhood, order, club, etc,) secret or not, hidden agenda, law or sovereignty group, occult, esoteric, New Age or Old Age.

The Cristian family supports and promotes the remedy that brings an everlasting peace, freedom, truth, joy, abundance and do no harm for all of life without causing loss of uniqueness or the need for having slaves and rulers. We are not into following the one in front or being shepherds for sheeple. Most importantly, we take full-responsibility for everything we think, feel and do.

The Cristian family are not Christians.

Arthur & Fiona Cristian
Love For Life

December 2006

The Cristian Family November 2006

THE CRISTIAN FAMILY PLEDGE

Being of clear brain, heart and intention, we each declare the following to be true:

• We have no intention of ending our own lives.

• We will not tolerate suppression of truth, ideas, freedom, or our work. We stand for freedom of speech.

• We stand together to support others in the expression of truths and freedom to speak out no matter how radical those ideas may seem.

• Standing for freedom takes courage; together we shall be strong in the face of all odds.

• If it is ever claimed that we have committed suicide, encountered an unfortunate accident, died of sickness/disease, disappeared, been institutionalized, or sold out financially or in any other way to self-interested factions, we declare those claims false and fabricated.

• We testify, assert and affirm without reservation, on behalf of all those who have dedicated their lives to the ending of secrecy and the promotion of freedom of thought, ideas and expression that we shall prevail.

• We Do Not Have Multiple Personality Disorders

Arthur Cristian
Fiona Cristian
Jasmin Lily Cristian
Emma Rose Cristian
Frances Hannah Cristian
Xanthe Jane Cristian

15th December 2006 (Edited/Updated 18th September 2011)

The Cristian Family November 2006

Update Regarding The Love For Life
Home Page And Quick User Guide

We are turning the Love for Life Quick User Guide http://loveforlife.com.au/node/6608 into a blog of all the main insights of our work since March 2005, whether through articles, videos, podcasts or discussions/debates.

As we do not have the time to compile everything we have written into a book, as many have suggested we do, compiling all our most important work into one area of the website is a way of providing easy access to this work so those interested are able to fully comprehend the big picture.

Instead of having to find our different articles, videos, etc, in various parts of the website, it will all be accessible here: http://loveforlife.com.au/node/6608 and here: http://loveforlife.com.au/node/3385.

Love For Life Videos

As amateurs and posted in the Quick User Guide below the Facebook links, we're currently creating and posting a series of videos called "The Dream Of Life" which covers the ground of all the Love For Life insights. We plan to have the videos completed by December 31st 2012. Once this is behind us, our intention is to create a 2 hour or so video covering the body of this work. All videos are embedded in the quick user guide http://loveforlife.com.au/node/6608 and uploaded in Arthur's YouTube channel: http://www.youtube.com/user/ArthurLoveForLife.

Love For Life Music

We have started recording songs, with others, that express the themes of Love For Life. They are now being posted on Arthur's YouTube channel: http://www.youtube.com/user/ArthurLoveForLife and are embedded in the quick user guide http://loveforlife.com.au/node/6608. We have over 100 songs to record. A few rough demos have already been used as the soundtrack on the first "Dream of Life" video.

About Us - Love For Life & The Cristian Family

Also, everything we, the Cristian family, have gone through, from bank fraud and the theft of the family home to death threats and attempts on Arthur's life, is documented in the Quick User Guide too. If you, the reader, are prepared to put the effort in, you will comprehend the extent to which we have all been tricked into becoming slaves, giving up our uniqueness and our full-responsibility for life and destroying everything of life to the point where life is in danger of dying out completely. You will also comprehend the remedy to all this chaos; a remedy that requires only love for life and the determination to do what needs to be done. Though our focus is very strongly on the remedy that creates a world of freedom, truth, peace, joy, abundance and Do No Harm for all of life without loss of uniqueness or the need for slaves and rulers, we realise that it is vital to comprehend how to get there and what stops us from getting there. This is why there is so much information on the hows and whys of everything going wrong in the world today. We are not into peddling conspiracy theories, we are into routing out all forms of organised crime.

Saturday 26th November 2011

Arthur and Fiona Cristian
Love For Life

Website: http://loveforlife.com.au
Email: action@loveforlife.com.au
Mobile: 0011 61 418 203204 - (0418 203204)
Facebook Arthur Cristian: http://www.facebook.com/arthurcristian
YouTube Arthur Cristian: http://www.youtube.com/ArthurLoveForLife
SoundCloud: http://soundcloud.com/loveforlife
Nimbit Music: http://www.nimbitmusic.com/loveforlife
Twitter: https://twitter.com/loveforlifemusi
Facebook Music: http://www.facebook.com/loveforlifemusic
Facebook Why Aren't We Free Discussion: http://www.facebook.com/164918753537287
Facebook Do No Harm Community: http://www.facebook.com/151811728195925
YouTube Love For Life Music: http://www.myspace.com/loveforlifemusic
MySpace: http://www.myspace.com/loveforlifemusic
Google + Fiona Cristian: https://plus.google.com/100490175160871610090
Register To The Love For Life Mailing List: http://loveforlife.com.au/content/09/05/14/mailing-list

1. For The Body Of The Love For Life Work by Arthur and Fiona Cristian

Which Unravels The Reasons For The Chaos, Mayhem and Confusion Being Experienced In The World Today, Explains The Need For "Community Immunity" and Responsibility, and Focuses On The Creation Of Kindoms - Do No Harm, Life-Sustainable Communities (As The Remedy That Heals All Mans Woes) - And How We Can Co-Create Them. For Comments, Articles And Discussions, Go Here: http://loveforlife.com.au/node/3385 - Also Go Here To See Podcasts And Videos Posted by Arthur & Fiona Cristian: http://loveforlife.com.au/node/7309 - The Information Shared Comes From Inspiration, Intuition, Heartfelt-Logic And Information Gathered From Nature And Many Amazing Men And Women Along The Way. It Is Not Found In Any Books Or Channellings, Or Talked About By "Experts". Go Here To Read A Brief Synopsis Of Why We Started Love For Life: http://loveforlife.com.au/node/8182

2. For Information About The Ringing Cedars of Russia Series

go here: http://loveforlife.com.au/node/1125 and for more on Eco Homes, Villages, Organic and Permaculture Gardening and Life-Sustainability, etc, go here: http://loveforlife.com.au/node/3641 and here: http://loveforlife.com.au/node/1985 and Mikhail Petrovich Shchetinin - Kin's School - Lycee School at Tekos: http://loveforlife.com.au/node/5173

3. For How To Eat A Raw, Living Food Diet,

go here: http://loveforlife.com.au/node/5068 - LIFE is information. When we distort LIFE and then eat, drink, absorb, think, feel, hear, see, touch, taste, smell and perform these distortions, the information of LIFE, your LIFE, our LIFE, our children's lives, everyone's LIFE, is distorted.

4. To Find A Menu For The Extensive Research Library (over 8,000 items posted embodying over 11,000 documents, pdf's, videos, podcasts, etc)

Which Covers Topics From Health to Chemtrails/Haarp to Brain Control to Archaeology to Astronomy Geocentricity Heliocentricity to Pandemics Bird Flu Swine Flu to Fluoride to Cancer to Free Energy to Global Warming, 9/11, Bali Bombings, Aspartame, MSG, Vaccinations, Aids/HIV, Mercury, New World Order, Satanism, Religions, Cults, Sects, Symbolism, etc, etc, go here: http://loveforlife.com.au/node/82

5. If You Would Like To Read About The Cristian Family NSW Supreme Court Case

(Macquarie Bank/Perpetual Limited Bank Fraud Condoned By Judges, Registrars, Barristers, Lawyers, Politicians, Public Servants, Bureaucrats, Big Business and Media Representatives - A Crime Syndicate/Terrorist Organisation) Which Prompted The Creation Of This Love For Life Website December 2006, And The Shooting And Torture Of Supporters Who Assisted Us In Reclaiming The Family Home, Joe Bryant And His Wife, Both In Their Late 70's, go here: http://loveforlife.com.au/node/5 And Read Some Of Our Email Correspondence With Lawyer Paul Kean - Macedone Christie Willis Solari Partners - Miranda Sydney May 17th-June 27th 2006: http://loveforlife.com.au/node/7300

6. For The Stories Of Other Victims Of The System,

go here: http://loveforlife.com.au/australian_stories (If you have a story you would like us to put up, we would love to here from you:
action @ loveforlife.com.au)

7. For Documentation Of Harm Done By The Powers-That-Be And Their Representatives,

Evidence Revealing How Victims Did Not Break The Peace, Caused No Crime or Harm, There Were No Injured Parties. Documenting Incontrovertible Evidence Demonstrating How The Powers That Be (PTB) And Their Lackeys Will Break All The Laws They Are Supposed To Uphold. They Will Kidnap, Intimidate, Terrorise, Rape, Pillage, Plunder And Lie And Take Responsibility For None Of It. All Part Of Their Tactics Of Using Fear And Trauma To Keep Us In Our Place. Relatives Of Those Under Their Radar Are Also Not Safe From Attack And Intimidation. All Starting From A $25 Fine For Not Voting And A $65 Fine For Not Changing A Dog Registration. We Do Not Have Freedom And Can Only Appear To Have Freedom If We Comply. Regardless How Small The Matter The PTB Throw Hundreds Of Thousands Of Dollars Away To Enforce Their Will.... Go Here:
Fiona Cristian Reply To State Debt Recovery Office - Part One to Part Ten - From 17th October 2008 And Still Continuing:
http://loveforlife.com.au/node/6319 or
Fiona Cristian Reply To State Debt Recovery Office
Part One: http://loveforlife.com.au/node/5742 - From 17th October 2008
Part Two: http://loveforlife.com.au/node/6135 - From 18th December 2008
Part Three: http://loveforlife.com.au/node/6295 - From 9th January 2009
Part Four: http://loveforlife.com.au/node/6296 - From 14th January 2009
Part Five: http://loveforlife.com.au/node/6375 - The Sick Puppy - From 20th February 2009
Part Six: http://loveforlife.com.au/node/6390 - Police Officers, Sheriff’s Officers, Tow Truck Driver and State Debt Recovery Office Blatantly Ignore the Law To Rape, Pillage and Plunder The Private Property Of Fiona Cristian - From 11th March 2009
Part Seven: http://loveforlife.com.au/node/6445 - Affidavit Of Truth - Letter To The Queen + Australia: Fascism is Corporatism - From 30th March 2009
Part Eight: http://loveforlife.com.au/node/6652 - The Pirates Auction And The Ghost Of VSL386 - From 4th April 2009
Part Nine: http://loveforlife.com.au/node/7073 - Arthur Cristian's Letter To Pru Goward MP - From 15th December 2009
Part Ten: http://loveforlife.com.au/node/7500 - Should We Be In Fear Of Those Who Claim To Protect Us? "Roman Cult" Canon Law - Ecclesiastical Deed Poll - The Work Of Frank O'Collins - From 13th October 2010

8. If You Are Interested In Information On Freedom From Statutes, Rule-Of-Law, Free Man/Free Woman, Strawman, "Person" and Admiralty Law (The Law Of Commerce),

go here: http://loveforlife.com.au/node/895 - For Common Law, Democracy, Constitution, Trial By Jury, Fee Simple, etc, go here: http://loveforlife.com.au/category/main/law-articles-documents

9. If You Are Interested In Banking and Money Created (Fiat/Credit/Debt/Mortgage/Loan/Overdraft etc) Out-Of-Thin-Air, How Banks Counterfeit Money,

go here: http://loveforlife.com.au/banks

10. For A List Of All The Latest Posts In The Love For Life Website,

go here: http://loveforlife.com.au/tracker

11. For Links To Many Hundreds Of Videos, DVDs And Podcasts

go here: http://loveforlife.com.au/video_dvd

12. To See The Cristian Family Pledge, Legal and other Disclaimers

go here: http://loveforlife.com.au/content/06/12/05/love-life-legal-disclaimer

13. To Read About How A Representative Of The NSW Jewish Board Of Deputies Had Threatened To Shut Down The Love For Life Website

go here: Part One: http://loveforlife.com.au/node/6616 Part Two: THE STEVE JOHNSON REPORT AND VIDEO: http://loveforlife.com.au/node/6665 and Part Three: Latest Update On James Von Brunn: http://loveforlife.com.au/node/6673

Conscious Love Always
Arthur & Fiona Cristian
Love For Life
action @ loveforlife.com.au
www.loveforlife.com.au
0418 203204 (int: 0011 61 418 203204)
PO Box 1320 Bowral 2576 NSW Australia

Arthur Cristian

Create Your Badge

Love For Life Discussions - Why Aren't We Free? How Can We Be Free?

Promote your Page too

The Cristian Family November 2006

Love For Life Legal Disclaimer

The information contained on this world wide web site (the web site and all information herein shall be collectively referred to as "Web Site Information"), under the registered url name, loveforlife.com.au, resides on a host server environment in Pittsburgh, Pennsylvania 15203, United States of America.

The Web Site Information has been prepared to provide general information only and is not intended to constitute or be construed as providing substantive professional advice or opinion on any facts or circumstances. Transmission of the information is not intended to create, nor does its receipt give rise to, a professional-client relationship between 'Love for Life' and the receiver.

While every care has been taken to ensure the accuracy and timeliness of the information prepared and/or reported on this site, 'Love for Life' is not responsible for any errors or omissions or for the Web Site Information not being up to date. The Web Site Information may not reflect the most current developments.

The impact of the law, policy and/or procedure for any particular situation depends on a variety of factors; therefore, readers should not act upon any Web Site Information without seeking professional advice. 'Love for Life' is not responsible for any action taken in reliance on any Web Site Information herein.

'Love for Life' is not responsible for any action you or others take which relies on information in this website and/or responses thereto. 'Love for Life' disclaim all responsibility and liability for loss or damage suffered by any person relying, directly or indirectly, on the Web Site Information, including in relation to negligence or any other default.

'Love for Life' does not warrant, represent or hold out that any Web Site Information will not cause damage, or is free from any computer virus, defect(s) or error(s). 'Love for Life' is not liable to users for any loss or damage however caused resulting from the use of material found on its web site.

'Love for Life' does not necessarily endorse or approve of any Web Site Information linked to and contained on other web sites linked herein and makes no warranties or representations regarding the merchantability or fitness for purpose, accuracy and quality, of any such information.

The sending of information by you, and the receipt of it by 'Love for Life', is not intended to, and does not, create a professional-client relationship.

All Web Site Information is considered correct at the time of the web site's most recent revision.

The Cristian Family November 2006

ADDITIONAL DISCLAIMER

THE CRISTIAN FAMILY SUPPORTS
FREEDOM OF SPEECH - FREEDOM OF THOUGHT

Note: Updated Wednesday 17th June 2009 8.00pm Sydney Time.

Love For Life does not support harm doing in any shape or form. However, we are supporters of free speech so we post articles, documentaries, etc, that represent a wide cross section of ideas. See the Love For Life extensive research library where there are over 11,000 individual documents, articles, videos, podcasts and debates/discussions are posted: http://loveforlife.com.au/node/82. We clearly see the evidence of the destruction to MAN and Earth that has been caused by ALL religions over the centuries and are therefore not supporters of religions, cults, sects or any group that demands conformity of thought, speech or action, or has rules, regulations or rituals that must be followed. Religions, nationalities and cultural "identities" are formed as a result of the brainwashing we receive from childhood. They are part of the tactics the Establishment uses to keep us all divided from one another and fighting one another.

All religions promote discrimination and division, leading to hatred and even violence and murder. None of them have yet to produce a remedy to all the suffering, poverty, unhappiness and discrimination in the world. If any religion truly had the remedy to all the suffering on earth, there would no longer be any suffering. What have Christianity, Islam, Buddhism, Hinduism, Judaism, atheism and the New Age done to end the suffering in the world?

Freedom Of Speech - Freedom Of Thought

Since December 2006, there have been many attempts to take down the Love For Life website. Any attempts have been thwarted by Love For Life supporters inundating the harm-doers with emails, etc, objecting to them taking down the website for a variety of reasons. The trouble makers usually back off when they realise that they can post all their views, arguments, beliefs, etc, in the Love For Life website without censorship or restriction imposed. They get to see that even the Queen, Pope, Prime Minister, President of America, etc, can post all their views without hindrance or sabotage and that we support freedom of speech/thought which means we support the right of all sides to express their views.

Of note, there is a vast amount of information posted in the Love For Life website which we do not agree with but we leave it all up because we refuse to be biased, opinionated or self-centered/self-serving. Of the many thousands of comments posted over the years we have only removed posts containing secret links to commercial advertisements, terrible foul language, threats of violence and death, etc, and attacks on other people's characters that avoid the subject/debate at hand. Besides links to advertisements, we have taken down less than six comments due to the above. We usually leave everything up, all warts and all, even those posts threatening to do terrible things to Fiona, our children, our dogs, our friends, family & supporters, etc.

The Love For Life website has information from all sides on many subjects, whether about Islam, Judaism, Christianity, Law, health, psychology, mind control, vaccination, aspartame, MSG, Chemtrails etc. There are over 11,000 individual articles, documentaries, podcasts, etc on the website and they are so diverse that we are sure that everyone would be able to find something they loved and something they hated, if they took the time to search. If we removed all the articles hated by everyone, there would probably be nothing left! We are not anti anyone but freedom of speech is freedom of speech and no one should condemn the work of another without taking the time to research the subject themselves. Yes, there are articles by those who have a less-than-rosy-viewpoint of Judaism, but there are also articles on the dark side of Tibetan Buddhism (and it is very dark) for those who are interested in the truth: Tibet - Buddhism - Dalai Lama: http://loveforlife.com.au/node/6271 Should the authors of these articles be abused and imprisoned for daring to challenge the widely conceived reputation of Buddhism as being the religion of peace and love and that of the Dalai Lama as a saint, or should those interested be allowed to study the work and come to their own conclusions? The same applies to all the articles, documentaries, etc, about Christianity, Islam, Freemasonry, New World Order, etc.

The Love for Life website also shows how the Rule of Law, the Bar, the Government, the Monarchy, the system of commerce, the local, national and multi/trans-national private corporations, all the courses and careers on offer from our universities, all the educators, scientists, academics and experts, the aristocrats and the Establishment bloodlines have also done NOTHING to end the suffering in the world. The website maps the insanity of a world where there is no help for those in need, just as there was no help available for us when we were victims of terrible bank fraud: http://loveforlife.com.au/court_case orchestrated, condoned and protected by an international crime syndicate/terrorist organisation of judges, barristers, registrars, lawyers, politicians, banksters, big business representatives, media moguls and other lackeys who, all together, put up a wall of silence despite our trying many, many avenues. After the family home was stolen and business destroyed we were left close to poverty and destitution caring for 4 young daughters. Three years later not much has changed regardless of all our efforts. Where were all the followers of all the religions to help us? Or do we have to be members of those religions to receive help from others involved in them?

We have been accused of being anti - Jewish because we had posted an excerpt from James von Brun's book: Kill the Best Gentiles! http://loveforlife.com.au/node/6054 in which he blames Jews for the problems of the world. Obviously this is not our view because of what we have stated above. We do not hate anyone, whatever religion they follow. We are always open to talk to any religious leader or politician and meet with any judge, member of the Bar, experts, academics, educators etc to share the remedy we offer that heals all the divisions between MAN and MAN, and MAN and EARTH.

Today, a representative of the New South Wales Jewish Board of Deputies is threatening to close the website down, because they have decided it is anti - Jewish and that we promote racism. What has the New South Wales Jewish Board of Deputies done to end the suffering in the world? Can they show that they are concerned with the suffering of ALL men, women and children AND ARE SEEN TO BE DOING SOMETHING ABOUT IT or are they only concerned with Jewish affairs? If so, they, along with all the other religions that only care for their own, are part of the problem, not part of the solution. The man who rang Arthur today was only concerned with Jewish affairs; he was not interested in our intentions or in anybody else, just as most Christians, Muslims, Sikhs, Catholics, etc, are only interested in their own. While we separate our lives into groups, dividing our lives from others with rules, regulations, rituals, procedures, conditions and contracts, we will never solve our problems.

No matter what we in the Western World Civilisation of Commerce have been promised by our politicians, religious leaders, scientists, educators, philosophers, etc, for the past two hundred years, all we have seen is ever-increasing destruction of men, women and children and Earth. None of the so-called experts and leaders we have been taught to rely on are coming up with a solution and none of them are taking full-responsibility for the fact that they can't handle the problem. All religious books talk about end times full of destruction and suffering but why do we have to follow this program when there is an alternative to hatred, mayhem and death? Why are our leaders following the program of destruction and death rather than exploring the do no harm alternatives? It seems that any mainstream politician, priest or academic are only interested in supporting the RULES OF THE DIVIDE, that maintain the haves and the have nots. For 200+ years, 99% of the world population have been so trained to pass on their responsibility for their lives, others and Earth, that the 1% of the population that make up the leaders of the rest of us are making all the decisions leading to the destruction of all of us and Earth. Let's not forget the education system that brainwashes the 99% of the population that we are free and have equal rights while, in fact, we are feathering the nests of those at the top.

At the root of all our problems is self-centredness, an unwillingness nurtured by the Establishment that keeps us concerned only with our own needs rather than the needs of others around us and Earth. Instead of creating and releasing acts of love for those around us as gifts to benefit them and Earth, we take, take and take, until there is nothing left. The whole point of the Love for Life website is to show people the root of all our problems and to share the remedy. The extensive research library is there to attract browsers and to provide access to information not available through mainstream channels. If the New South Wales Jewish Board of Deputies can, after careful examination of our work, prove that anything we are saying is wrong, we will be happy to accept their proof. If they cannot, and they are still insistent on closing the website down, they will be showing themselves to be traitors to MAN because they are not interested in pursuing any avenue that can end the suffering in the world.

All religions, corporations and organisations that support and maintain the Western World Civilisation of Commerce are part of the problem because our civilisation is a world of haves and have nots, exclusivity, privilege, racism, violence, hatred, poverty, sickness, discrimination, abuse, starvation, homelessness, corruption, collusion, vindictiveness, social unrest, arrogance, ignorance, fear, war and chaos. While we support civilisation, we support death and destruction.

If we truly want peace and freedom for all, we have to let go of all that which keeps us divided, and come together as MAN, conscious living co-creators of creation/life. The Love For Life website offers a remedy to the problems we all face in the form of DO NO HARM COMMUNITIES (KINDOMS): http://loveforlife.com.au/node/6608 - http://loveforlife.com.au/node/3641 For more details see here: http://loveforlife.com.au/node/6511 and here: http://loveforlife.com.au/node/3385 - We also highly recommend that everyone read the brilliant Russian books called The Ringing Cedars: http://loveforlife.com.au/node/1125 - The Love For Life homepage/front-page also provides lots of inspiring remedy based information: http://loveforlife.com.au - If you want to be kept up to date with our work please register to the Love For Life mailing list here: http://loveforlife.com.au/campaign_list We usually send two postings per month. Presently (September 2011) there are over 7000 registrations reaching over 500,000 readers across Earth. The website now (September 2011) receives up to 12 million hits per month. Since December 2006, over 100 million people have visited the Love For Life website.

Conscious Love Always
Arthur and Fiona Cristian
Love For Life
17th June 2009

The Cristian Family November 2006

Clarification Regarding Our Intentions
Behind The Use Of Donations

The Love For Life website is offered for free without a fee and without any conditions attached. If people are inspired to donate money, then we accept their gift and have provided an avenue for them to support the work we do through Fiona's Paypal or ANZ bank account http://loveforlife.com.au/node/8515. There is no obligation whatsoever to donate and all are equally welcome to our work and to our "time", whether they donate or not. Over the last 9 years, all the Love For Life work has been put out for free and it has often been donations from supporters that have enabled us to renew the domain name, etc, to keep the website going. While some complain that we have an avenue for donations, others complained when we didn't! Either use it or don't - the choice is yours.

Since Love For Life started March 2005 and website December 2006, Arthur has worked 16 hours a day, 7 days a week unpaid for much of this period, putting together the website and sharing insights to wake people up to what has been done to them, whether through the 11,500+ individual articles, videos, podcasts, debates, discussions, pdf's, research documents, etc, found amongst the 8,500+ posts, as well as helping many, many men and women over the phone, and through email, website correspondence, Facebook and YouTube, and creating the Love For Life food forest vege garden and Love For Life music recording studio. This is our life is a gift commitment to serve MAN/Nature/Earth but we are still severely compromised by "The System" and still have to give to Caesar what is claimed to belong to Caesar, which is where the donations help us.

Fiona & Arthur Cristian
Love For Life
21st July 2014